Home » Icom Manuals » Two-Way Radios » Icom IC-7610 » Manual Viewer

Icom IC-7610 Instruction Manual advanced - Page 83

Selecting the antenna connector, ANT MW

Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

10. ANTENNA TUNER OPERATION (ADVANCED) Selecting the antenna connector Set the antenna connector to "ANT1" or "ANT2," and turn the receive antenna connector ON or OFF. 1. Select the Main band or Sub band. 2. Select the operating band. 3. Touch [ANT] in the Multi-function key group to set to "ANT1" or "ANT2." LWhile "ANT1" is selected, touch [ANT] for 1 second to set the antenna that is connected to [ANT1] for transmitting, and the antenna connected to [RX-ANT IN] for receiving. When not using the [RX-ANT] connector, Set "ANT1" or "ANT2." LWhen "ANT1/R" or "ANT2/R" is selected, the signal is switched to the [RX-ANT IN] connector, and then reception in the [ANT1] and [ANT2] are disconnected. LWhile "ANT2" is selected, touch [ANT] for 1 second to set the antenna that is connected to [ANT2] for transmitting, and the antenna connected to [RX-ANT IN] for receiving is displayed if you temporarily select an antenna that is different from the one that is saved in memory. - Touch [ANT MW] for 1 second to save the temporary selection into memory, then "" disappears. MENU » ANTENNA > ANT MW ••When the antenna selection mode ([ANT] SW) is set to "Manual," each antenna connector is selected according to the saved settings. MENU » ANTENNA > [ANT] SW 77

Section	Page
Top cover	1
Table of contents	2
1. ADVANCED CONNECTIONS	5
137 kHz band operation (European version only)	5
Connecting the RC-28	6
Using the RC-28	6
FSK, AFSK, PSK connections	7
Connecting the AH-740	8
2. ADVANCED OPERATIONS	9
Band Edge Beep	9
Entering Band Beep Edges	9
Adjusting the Drive Gain level	13
IP Plus function	13
Tracking function	14
VOX function	15
Adjusting the VOX function	15
Turning ON the VOX function	15
Delta TX function	16
Delta TX monitor function	16
Operating CW (ADVANCED)	17
About the CW Reverse mode	17
Using the Memory Keyer function (KEYER)	17
Keyer memory edit menu (EDIT)	18
Contest number menu (001 SET)	19
Keyer set menu (CW-KEY SET)	20
Operating RTTY (FSK)	21
Displaying the RTTY DECODE screen	22
RTTY decoding	22
Twin Peak Filter (TPF)	22
Transmitting an RTTY memory content	23
Setting the RTTY Automatic TX/RX	24
Editing an RTTY memory	25
Turning ON the RTTY log	26
Viewing the RTTY log contents	27
RTTY Decode Log set	27
Operating PSK	29
Displaying the PSK DECODE screen	29
PSK decoding	30
AFC/NET function	30
Transmitting a PSK memory content	31
Setting the PSK Automatic TX/RX	32
Editing a PSK memory	33
Turning ON the PSK log	34
Viewing the PSK log contents	35
PSK Decode Log set	35
FM repeater operation	37
Setting the repeater tone frequency	37
Checking the repeater input signal	38
Tone squelch operation	39
Data mode (AFSK) operation	40
Transverter operation	40
Transverter setting example	40
About the 5 MHz frequency band operation (USA version only)	41
3. ADVANCED SCOPE OPERATION	42
Spectrum Scope screen	42
Center mode	42
Fixed mode	42
Directly tuning to a signal	43
Dual Scope screen	43
Sweep speed	44
Adjusting the Reference level	44
SCOPE SET screen	45
4. VOICE RECORDER FUNCTIONS	48
Recording a QSO audio	48
Using the [REC] key	48
Using the [QUICK] key	48
Using the MENU screen	48
Playing back a QSO audio	49
Playing back a recorded audio on a PC	50
Checking the folder information and file information	51
Deleting files	52
Deleting folders	52
RECORDER SET screen	53
PLAYER SET screen	54
INSTANT REPLAY SET screen	55
Instant Replay function	55
Recording the Instant Replay	55
Playing back the Instant Replay	55
5. VOICE TX MEMORY OPERATION	56
Recording a Voice TX memory	56
Recording	56
Playing back	56
Entering a Voice TX memory name	57
Transmitting a Voice memory content	58
Transmitting	58
Repeatedly transmitting	59
Adjusting the output level	59
VOICE TX SET screen	60
6. SD CARD/USB FLASH DRIVE (ADVANCED)	61
Saving the setting data onto an SD card or USB flash drive	61
Loading the saved data files onto an SD card or USB flash drive	62
Deleting a data file	63
Displaying the SD card or USB flash drive information	64
About the SD card and USB flash drive’s folders	65
The SD card folder	65
USB flash drive folder	65
7. MEMORY OPERATION	66
Memory channels	66
Selecting a Memory channel	66
Entering memory channel contents	67
Copying the Memory channel contents	68
Copying to the VFO	68
Copying to the other Memory channel	68
Entering a memory name	69
Clearing a memory channel	70
About the MEMORY screen	70
Memo Pad	71
Saving the displayed contents into a Memo Pad	71
Calling up the Memo Pads	71
8. SCANS	72
Scan types	72
Preparation	72
Squelch status	72
SCAN screen	73
SCAN SET screen	73
Programmed scan	74
Programmed scan operation	74
Memory scan	75
Memory scan operation	75
Setting the Select Memory channels	75
Memory scan operation	76
9. CLOCK AND TIMERS (ADVANCED)	78
NTP function	78
Using the NTP Time Synchronize function	78
Using the NTP function	78
Setting the Timers	79
Setting the Sleep Timer	79
Setting the Daily Timer	80
Daily Timer setting items	81
10. ANTENNA TUNER OPERATION (ADVANCED)	82
Using the [RX-I/O] in the Dualwatch operation	82
Selecting the antenna connector	83
11. OTHER FUNCTIONS	84
RF Direct Sampling System	84
About the RF/SQL Control	85
About “USB SEND/Keying”	86
Measuring SWR	87
Selecting the Display Type	88
Selecting the Display Font	88
Displaying my call sign	88
Screen Capture function	89
Setting the Screen Capture function	89
Capturing a screen	89
Viewing a captured screen	89
REF adjustment	90
12. MAINTENANCE (ADVANCED)	91
Cleaning	91
Replacing fuse	91
DC power cable fuses	91
Circuitry fuse	92
Touch screen calibration function	93
13. UPDATING THE FIRMWARE	94
General	94
About updating the firmware	94
Checking the firmware version	94
Preparation	95
Unzipping the firmware folder	95
Updating the firmware	96
INDEX	98