Lexmark J110 Service Manual - Page 191

Paper Feed Pick Arm Assembly with Motor and Paper Path Sensor Removal, Power Supply Removal

Get Lexmark J110 PDF manuals and user guides View all Lexmark J110 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 191 highlights

4085-001 Paper Feed Pick Arm Assembly with Motor and Paper Path Sensor Removal 1. Remove all covers. 2. Remove power supply. Refer to "Power Supply Removal" on page 4-19. 3. Remove the frame from the base. Refer to "Frame From Base Removal" on page 4-27. 4. Remove the two lower screws on the base of the RIP shield. 5. Disconnect the integrated tray connector (J6) from the engine board and disconnect the paper path sensor. 6. Remove the E-clip {A} from the pick assembly shaft. 7. Remove the screw {B} from the paper feed frame assembly. 8. Slide the shaft to the left and remove the pick arm assembly. 9. Disconnect the wire from the paper path sensor and snap the sensor out to remove. When reinstalling, note the routing of the wires and position of spring. Repair Information 4-31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
Repair Information
4-31
4085-001
Paper Feed Pick Arm Assembly with Motor and Paper
Path Sensor Removal
1.
Remove all covers.
2.
Remove power supply. Refer to
“Power Supply Removal” on
page 4-19
.
3.
Remove the frame from the base. Refer to
“Frame From Base
Removal” on page 4-27
.
4.
Remove the two lower screws on the base of the RIP shield.
5.
Disconnect the integrated tray connector (J6) from the engine
board and disconnect the paper path sensor.
6.
Remove the E-clip {A} from the pick assembly shaft.
7.
Remove the screw {B} from the paper feed frame assembly.
8.
Slide the shaft to the left and remove the pick arm assembly.
9.
Disconnect the wire from the paper path sensor and snap the
sensor out to remove. When reinstalling, note the routing of the
wires and position of spring.