Oki X400 X400 Programming Command Manual - Page 90

Calibrate Sensor

Get Oki X400 PDF manuals and user guides View all Oki X400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 90 highlights

Calibrate Sensor Command Structure CA Example: CA Placement: This command should be sent after the sensor type has been selected with the CI command. It should not be included with print job commands. Default: There is no default for this command. Command Function To adjust the label sensor for unique media and ribbon combinations. Input to Printer Printer Output A CI2 CA Z There is no printer output for of this command. It will cause the printer to feed about 6 inches while the characteristics of the label backing or eyemark are measured. Special Notes 1. The sensor is calibrated for the currently selected sensor type (Eye-Mark or transmissive). 2. The sensor must be recalibrated whenever the sensor type is changed or incorrect label detection occurs. 3 When calibrating the sensor for the OKIPOS X400 Thermal Transfer unit operating in the thermal transfer mode, the ribbon must be installed in the printer. 88

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
Calibrate Sensor
Command Structure
<ESC>CA
Example:
<ESC>CA
Placement: This command should be sent after the sensor type has been
selected with the <ESC>CI command. It should not be included
with print job commands.
Default:
There is no default for this command.
Command Function
To adjust the label sensor for unique media and ribbon combinations.
Input to Printer
<ESC>A
<ESC>CI2
<ESC>CA
<ESC>Z
Printer Output
There is no printer output for of this command. It will cause the printer to
feed about 6 inches while the characteristics of the label backing or eye-
mark are measured.
Special Notes
1.
The sensor is calibrated for the currently selected sensor type (Eye-Mark or
transmissive).
2.
The sensor must be recalibrated whenever the sensor type is changed or in-
correct label detection occurs.
3
When calibrating the sensor for the OKIPOS X400 Thermal Transfer unit operating in
the thermal transfer mode, the ribbon must be installed in the printer.
88