Panasonic PT-DZ21KU Operating Instructions - Page 100
[cooling Condition], [high Altitude Mode], [lamp Select], The <enter> Button.
View all Panasonic PT-DZ21KU manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 100 highlights
[PROJECTOR SETUP] menu [COOLING CONDITION] Change the fan control depending on the direction of projection. Set [COOLING CONDITION] correctly in accordance with the direction of projection referencing the following figure. It may shorten the life of the lamp if used in incorrect setting. 1) Press ▲▼ to select [COOLING CONDITION]. 2) Press the button. zzThe [COOLING CONDITION] screen is displayed. 3) Press ▲▼ to select a cooling condition. [VERTICAL UP SETTING] [FLOOR SETTING] [CEILING SETTING] [VERTICAL DOWN SETTING] ɿ Projection direction 4) Press the button. 5) When the confirmation is displayed, select [OK] or [CANCEL], and press the button. Note zzCannot be set when using the optional accessory replacement lamp unit (for portrait mode) (Model No.: ET-LAD510P (1 pc), ET-LAD510PF (4 pcs)) (fixed to [PORTRAIT SETTING]). [HIGH ALTITUDE MODE] Set to [ON] to use the projector at 1 400 m (4 593 ft) to 2 700 m (8 858 ft) elevations. 1) Press ▲▼ to select [HIGH ALTITUDE MODE]. 2) Press ◀▶ to switch [HIGH ALTITUDE MODE]. [OFF] [ON] [OFF] [ON] When using at a place lower than 1 400 m (4 593 ft) above sea level When using at a high altitude (1 400 m (4 593 ft) or higher and lower than 2 700 m (8 858 ft) above sea level) 3) When the confirmation is displayed, select [OK] or [CANCEL], and press the button. 100 - ENGLISH Note zzThe speed of the fan increases and the operation sound becomes louder when set to [ON]. zzThe optional smoke cut filter cannot be used when in high elevation mode. [LAMP SELECT] Select luminous lamps from the four equipped in the projector body to turn on for a certain use condition or purpose. 1) Press ▲▼ to select [LAMP SELECT]. 2) Press ◀▶ to switch [LAMP SELECT]. zzThe setting will change as follows each time you press the button. [L1] [L2] [QUAD] (4 lit) [L3] [TRIPLE] (3 lit) [L4] [DUAL] (2 lit) [L1/L4] [SINGLE] (1 lit) [L2/L3] [L2/L3/L4] [L1/L2/L3] [L1/L3/L4] [L1/L2/L4] [L1] [L2] [L3] [L4] [L1/L4] [L2/L3] [L1/L2/L3] [L1/L2/L4] [L1/L3/L4] [L2/L3/L4] [SINGLE] (1 lit) [DUAL] (2 lit) [TRIPLE] (3 lit) [QUAD] (4 lit) Lamp 1 will light. Lamp 2 will light. Lamp 3 will light. Lamp 4 will light. Lamp 1 and Lamp 4 will light. Lamp 2 and Lamp 3 will light. Lamp 1, Lamp 2 and Lamp 3 will light. Lamp 1, Lamp 2 and Lamp 4 will light. Lamp 1, Lamp 3 and Lamp 4 will light. Lamp 2, Lamp 3 and Lamp 4 will light. One lamp will light. (A short usage time lamp will automatically light.) Two lamps will light. (A short usage time lamp will automatically light.) Three lamps will light. (A short usage time lamp will automatically light.) Four lamps will light. 3) Press the button. Settings