Home » Panasonic Manuals » Projectors » Panasonic PT-DZ21KU » Manual Viewer

Panasonic PT-DZ21KU Operating Instructions - Page 173

English - 173, <3d Sync 2 Out&gt

View all Panasonic PT-DZ21KU manuals

Add to My Manuals
Save this manual to your list of manuals

Page 173 highlights

Specifications Model No. PT-DZ21KU PT-DS20KU PT-DW17KU Contrast ratio 10 000:1 (when [DYNAMIC IRIS] is set to [3]) terminal 1 set (BNC x 5 (RGB/YPBPR/YCBCR/YC x 1)) [RGB signal] 0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω) HD/SYNC TTL high impedance, automatic positive/negative polarity compatible VD TTL high impedance, automatic positive/negative polarity compatible [YPBPR signal] Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω [Y/C signal] Y: 1.0 V [p-p], C: 0.286 V [p-p] 75 Ω terminal 1 set, high-density D-Sub 15p (female) [RGB signal] 0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω) HD/SYNC TTL high impedance, automatic positive/negative polarity compatible VD TTL high impedance, automatic positive/negative polarity compatible [YPBPR signal] Y: 1.0 V [p-p] including synchronization signal, PBPR: 0.7 V [p-p] 75 Ω terminal 1 set, BNC 1.0 V [p-p] 75 Ω terminal 1 set, DVI-D 24 p single link, DVI 1.0 compatible, HDCP compliant terminal 1 set, HDMI 19 pin, (HDCP and Deep color compatible) 1 set (BNC) [SD-SDI signal] SMPTE ST 259 compliant Terminals terminal [HD-SDI signal] [3G-SDI signal] SMPTE ST 292 compliant SMPTE ST 424 compliant - [Dual link HD-SDI (LINK-A) signal] SMPTE ST 372 compliant 1 set (BNC) [SD-SDI signal] SMPTE ST 259 compliant terminal [HD-SDI signal] SMPTE ST 292 compliant - [Dual link HD-SDI (LINK-B) SMPTE ST 372 compliant signal] 1 set (BNC) terminal During input setting TTL high impedance - During output setting TTL output max. 10 mA 1 set (BNC) terminal TTL output max. 10mA - / terminal D-Sub 9 p, each set, RS-232C compatible, for computer control / terminal M3 stereo mini jack, each set, remote control for serial control terminal 1 set D-Sub 9 p for contact control terminal 1 set, (for RJ-45 network connection, PJLink compatible, 10Base-T/100Base-TX) Power cable length 3.0 m (118-1/8") Outer case Molded plastic Appendix ENGLISH - 173

Section	Page
Important Information	2
Read this first!	2
Precautions for use	15
Cautions when transporting	15
Cautions when installing	15
Security	18
Disposal	18
Cautions on use	18
Accessories	19
Optional accessories	20
Preparation	21
Start-up display	21
About your projector	22
Remote control	22
Projector body	24
Using the remote control	27
Inserting and removing the batteries	27
Setting Remote control ID numbers	27
Connecting to the projector with a cable	27
Getting Started	28
Setting up	28
Projection method	28
Parts for ceiling mount (optional)	29
Screen size and throw distance	29
Adjusting adjustable feet	42
Attaching/removing the projection lens (optional accessory)	43
Attaching the projection lens	43
Removing the projection lens	43
Connecting	44
Before connecting	44
Connecting example: AV equipment	45
Connecting example: Computers	47
Basic Operation	48
Switching on/off the projector	48
Connecting the power cord	48
Power indicator	49
Switching on the projector	50
Making adjustments and selections	50
Switching off the projector	51
Projecting	52
Select the input signal	52
Adjusting the focus, zoom, and shift	52
Moving the lens to the home position	53
Adjustment range by the lens position shift (optical shift)	54
Adjusting the lens mounter when the focus is unbalanced	55
Remote control operation	58
Using the shutter function	58
Using the on-screen display function	58
Switching the input	58
Using the STATUS function	59
Using the Automatic setup function	59
Using the Function button	59
Displaying the internal test pattern	60
Changing the picture aspect ratio	60
Settings	61
Menu navigation	61
Navigating through the menu	61
Main menu	62
Sub-menu	63
[PICTURE] menu	65
[PICTURE MODE]	65
[CONTRAST]	66
[BRIGHTNESS]	66
[COLOR]	66
[TINT]	66
[COLOR TEMPERATURE]	66
[GAMMA]	68
[SYSTEM DAYLIGHT VIEW]	68
[SHARPNESS]	68
[NOISE REDUCTION]	69
[DYNAMIC IRIS]	69
[SYSTEM SELECTOR]	70
Making sRGB compliant images	71
[POSITION] menu	72
[SHIFT]	72
[ASPECT]	72
[ZOOM]	73
[CLOCK PHASE]	74
[GEOMETRY] (PT‑DZ21KU and PT‑DS20KU only)	74
[KEYSTONE] (PT-DW17KU only)	76
[ADVANCED MENU]	77
[DIGITAL CINEMA REALITY]	77
[BLANKING]	77
[INPUT RESOLUTION]	78
[CLAMP POSITION]	78
[EDGE BLENDING]	78
[FRAME RESPONSE]	80
[FRAME LOCK] (PT‑DZ21KU and PT‑DS20KU only)	80
[RASTER POSITION]	80
[DISPLAY LANGUAGE] menu	81
Changing the display language	81
[3D SETTINGS] menu (PT‑DZ21KU and PT‑DS20KU only)	82
[3D SYSTEM SETTING]	82
[3D SYNC SETTING]	82
[3D SIMUL INPUT SETTING]	83
[3D INPUT FORMAT]	84
[LEFT/RIGHT SWAP]	84
[3D COLOR MATCHING]	84
[3D PICTURE BALANCE]	85
[DARK TIME SETTING]	85
[3D FRAME DELAY]	86
[3D TEST MODE]	86
[3D TEST PATTERN]	86
[SAFETY PRECAUTIONS MESSAGE]	87
[3D SAFETY PRECAUTIONS]	87
[DISPLAY OPTION] menu	88
[COLOR MATCHING]	88
[LARGE SCREEN CORRECTION]	89
[SCREEN SETTING] (PT‑DZ21KU and PT‑DS20KU only)	90
[AUTO SIGNAL]	90
[AUTO SETUP]	91
[RGB IN] (supported during RGB signal input only)	92
[DVI-D IN]	92
[HDMI IN]	93
[SDI IN] (PT‑DZ21KU and PT‑DS20KU only)	93
[ON-SCREEN DISPLAY]	94
[BACK COLOR]	95
[STARTUP LOGO]	95
[UNIFORMITY]	95
[SHUTTER SETTING]	96
[FREEZE]	96
[WAVEFORM MONITOR]	96
[CUT OFF]	98
[PROJECTOR SETUP] menu	99
[PROJECTOR ID]	99
[PROJECTION METHOD]	99
[COOLING CONDITION]	100
[HIGH ALTITUDE MODE]	100
[LAMP SELECT]	100
[LAMP RELAY]	101
[BRIGHTNESS CONTROL]	102
[STANDBY MODE]	106
[SCHEDULE]	106
[RS-232C]	108
[STATUS]	109
[NO SIGNAL SHUT-OFF]	110
[REMOTE2 MODE]	110
[FUNCTION BUTTON]	110
[DATE AND TIME]	110
[LENS CALIBRATION]	111
[LENS MEMORY]	112
[SAVE ALL USER DATA]	113
[LOAD ALL USER DATA]	113
[INITIALIZE]	114
[SERVICE PASSWORD]	114
[P IN P] menu	115
Using P IN P functions	115
Setting P IN P functions	115
[TEST PATTERN] menu	117
[TEST PATTERN]	117
[SIGNAL LIST] menu	118
Registering a signal to the list	118
Renaming the registered data	118
Deleting the registered data	118
Protecting the registered data	119
Expanding signal lock-in range	119
Managing the sub memory list	120
[SECURITY] menu	121
[SECURITY PASSWORD]	121
[SECURITY PASSWORD CHANGE]	121
[DISPLAY SETTING]	122
[TEXT CHANGE]	122
[CONTROL DEVICE SETUP]	122
[CONTROL DEVICE PASSWORD CHANGE]	124
[NETWORK] menu	125
[NETWORK SETUP]	125
[NETWORK CONTROL]	125
[NETWORK STATUS]	125
Network connections	126
Accessing from the Web browser	127
Maintenance	142
Lamp/Temperature/Filter Indicators	142
Managing the indicated problems	142
Maintenance/replacement	144
Before maintaining/replacing the unit	144
Maintenance	144
Replacing the unit	146
Troubleshooting	151
Self-diagnosis display	153
Appendix	156
Technical information	156
PJLink protocol	156
Control commands via LAN	157
<SERIAL IN>/<SERIAL OUT> terminal	160
<REMOTE 2 IN> terminal	164
Two window display combination list	165
Control device password	166
Upgrade kit (only supports PT‑DZ21KU and PT‑DS20KU)	166
List of compatible signals	167
Specifications	172
Dimensions	175
Ceiling mount bracket safeguards	176

Match case Limit results 1 per page

Speciﬁcations

ENGLISH - 173

Appendix

Model No.

PT-DZ21KU

PT-DS20KU

PT-DW17KU

Contrast ratio

10 000:1 (when [DYNAMIC IRIS] is set to [3])

Terminals

terminal

1 set (BNC x 5 (RGB/YP

/YC

/YC x 1))

[RGB signal]

0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)

HD/SYNC TTL high impedance, automatic positive/negative

polarity compatible

VD TTL high impedance, automatic positive/negative polarity

compatible

[YP

signal]

Y: 1.0 V [p-p] including synchronization signal, P

: 0.7 V [p-p]

75 Ω

[Y/C signal]

Y: 1.0 V [p-p], C: 0.286 V [p-p] 75 Ω

terminal

1 set, high-density D-Sub 15p (female)

[RGB signal]

0.7 V [p-p] 75 Ω (SYNC ON GREEN: 1.0 V [p-p] 75 Ω)

HD/SYNC TTL high impedance, automatic positive/negative

polarity compatible

VD TTL high impedance, automatic positive/negative polarity

compatible

[YP

signal]

Y: 1.0 V [p-p] including synchronization signal, P

: 0.7 V [p-p]

75 Ω

terminal

1 set, BNC 1.0 V [p-p] 75 Ω

<DVI-D IN>

terminal

1 set, DVI-D 24 p single link, DVI 1.0 compatible, HDCP compliant

terminal

1 set, HDMI 19 pin, (HDCP and Deep color compatible)

terminal

1 set (BNC)

—

[SD-SDI signal]

SMPTE ST 259 compliant

[HD-SDI signal]

SMPTE ST 292 compliant

[3G-SDI signal]

SMPTE ST 424 compliant

[Dual link HD-SDI (LINK-A)

signal]

SMPTE ST 372 compliant

terminal

1 set (BNC)

—

[SD-SDI signal]

SMPTE ST 259 compliant

[HD-SDI signal]

SMPTE ST 292 compliant

[Dual link HD-SDI (LINK-B)

signal]

SMPTE ST 372 compliant

<3D SYNC 1 IN/

OUT> terminal

1 set (BNC)

—

During input setting

TTL high impedance

During output setting

TTL output

max. 10 mA

<3D SYNC 2 OUT>

terminal

1 set (BNC)

—

TTL output

max. 10mA

<SERIAL IN>/

terminal

D-Sub 9 p, each set, RS-232C compatible, for computer control

<REMOTE 1 IN>/

terminal

M3 stereo mini jack, each set, remote control for serial control

terminal

1 set D-Sub 9 p for contact control

<LAN> terminal

1 set, (for RJ-45 network connection, PJLink compatible, 10Base-T/100Base-TX)

Power cable length

3.0 m (118-1/8")

Outer case

Molded plastic