Panasonic PT-DZ21KU Operating Instructions - Page 106

[STANDBY MODE], [SCHEDULE], How to assign a program

Get Panasonic PT-DZ21KU PDF manuals and user guides View all Panasonic PT-DZ21KU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

[PROJECTOR SETUP] menu 10) Set [BRIGHTNESS CONTROL GAIN] of all projectors to 100%. 11) Set [BRIGHTNESS CONTROL GAIN] of the darkest projector to 90%. 12) Adjust [BRIGHTNESS CONTROL GAIN] to match the [BRIGHTNESS CONTROL GAIN] set to 90% of the other projectors. 13) Set [MODE] in [BRIGHTNESS CONTROL SETUP] of all projectors to [AUTO], and [LINK] to [GROUP A]. 14) Select [APPLY] in [BRIGHTNESS CONTROL SETUP] on all projectors and press the button. zzLuminance control starts. Note zzBrightness is automatically corrected each time the lamp blinks when the power is switched on or off. zzAdjust luminance control again when variation in brightness has increased or a lamp is replaced. [STANDBY MODE] Set the power consumption during the standby. 1) Press ▲▼ to select [STANDBY MODE]. 2) Press ◀▶ to switch [STANDBY MODE]. zzThe setting will change as follows each time you press the button. [NORMAL] [ECO] Note zzWhen set to [ECO], network functions and terminal, and some RS-232C commands are not available during standby. The lighting for the connecting terminals and control panel does not turn on. zzWhen an error or warning occurs, a self diagnosis is displayed on the control panel regardless of the [STANDBY MODE] setting. ( page 25) zzWhen set to [ECO], the time taken to start display may be approximately ten seconds slower than compared to when set to [NORMAL]. [SCHEDULE] Set the command execution schedule for each day of the week. 1) Press ▲▼ to select [SCHEDULE]. 2) Press ◀▶ to switch [SCHEDULE]. zzThe setting will change as follows each time you press the button. [ON] [OFF] Note zzIf [SCHEDULE] is set to [ON], the setting for [STANDBY MODE] is automatically set to [NORMAL] and cannot be changed. Even if [SCHEDULE] is then set to [OFF] when in this state, the setting of [STANDBY MODE] remains at [NORMAL]. ■■How to assign a program 3) Select [ON] in Step 2), and press the button. zzThe [SCHEDULE] screen is displayed. 4) Select and assign program to each day of week. zzPress ▲▼ to select the day of week, and press ◀▶ to select a program number. zzYou can set the program from No.1 to No.7. "- -" indicates that the program number has not been set yet. ■■How to set a program You can set up to 16 commands to each program. 3) Select [ON] in Step 2), and press the button. zzThe [SCHEDULE] screen is displayed. 4) Press ▲▼ to select [PROGRAM EDIT]. 5) Press ◀▶ to select a program number and then press the button. 6) Press ▲▼ to select a command number and press the button. zzYou can change the page using ◀▶ . 7) Press ▲▼ to select [TIME] and press the button. 8) Press ◀▶ to select hour and minute, and press ▲▼ or the number ( to ) buttons on the remote control to set a time, and press the button. 9) Press ▲▼ to select [COMMAND]. Settings 106 - ENGLISH

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
[PROJECTOR SETUP] menu
106 - ENGLISH
Settings
10)
Set [BRIGHTNESS CONTROL GAIN]
of all projectors to 100%.
11)
Set [BRIGHTNESS CONTROL GAIN]
of the darkest projector to 90%.
12)
Adjust [BRIGHTNESS CONTROL
GAIN] to match the [BRIGHTNESS
CONTROL GAIN] set to 90% of the
other projectors.
13)
Set [MODE] in [BRIGHTNESS
CONTROL SETUP] of all projectors to
[AUTO], and [LINK] to [GROUP A].
14)
Select [APPLY] in [BRIGHTNESS
CONTROL SETUP] on all projectors
and press the <ENTER> button.
▶
z
Luminance control starts.
Note
z
Brightness is automatically corrected each time the
lamp blinks when the power is switched on or off.
z
Adjust luminance control again when variation in
brightness has increased or a lamp is replaced.
[STANDBY MODE]
Set the power consumption during the standby.
1) Press
▲▼
to select [STANDBY MODE].
2) Press
◀±
to switch [STANDBY
MODE].
▶
z
The setting will change as follows each time
you press the button.
[NORMAL]
[ECO]
Note
z
When set to [ECO], network functions and <SERIAL
OUT> terminal, and some RS-232C commands are
not available during standby. The lighting for the
connecting terminals and control panel does not
turn on.
z
When an error or warning occurs, a self diagnosis
is displayed on the control panel regardless of the
[STANDBY MODE] setting. (
page 25)
z
When set to [ECO], the time taken to start display
may be approximately ten seconds slower than
compared to when set to [NORMAL].
[SCHEDULE]
Set the command execution schedule for each day of
the week.
1) Press
▲▼
to select [SCHEDULE].
2) Press
◀±
to switch [SCHEDULE].
▶
z
The setting will change as follows each time
you press the button.
[ON]
[OFF]
Note
z
If [SCHEDULE] is set to [ON], the setting for
[STANDBY MODE] is automatically set to
[NORMAL] and cannot be changed. Even if
[SCHEDULE] is then set to [OFF] when in this
state, the setting of [STANDBY MODE] remains at
[NORMAL].
▶
■
How to assign a program
3) Select [ON] in Step 2), and press the
<ENTER> button.
▶
z
The
[SCHEDULE]
screen is displayed.
4) Select and assign program to each day
of week.
▶
z
Press
▲▼
to select the day of week, and press
◀±
to select a program number.
▶
z
You can set the program from No.1 to No.7. “-
- -” indicates that the program number has not
been set yet.
▶
■
How to set a program
You can set up to 16 commands to each program.
3) Select [ON] in Step 2), and press the
<ENTER> button.
▶
z
The
[SCHEDULE]
screen is displayed.
4) Press
▲▼
to select [PROGRAM EDIT].
5) Press
◀±
to select a program number
and then press the <ENTER> button.
6) Press
▲▼
to select a command
number and press the <ENTER>
button.
▶
z
You can change the page using
◀±
.
7) Press
▲▼
to select [TIME] and press
the <ENTER> button.
8) Press
◀±
to select hour and minute,
and press
▲▼
or the number (<0> to
<9>) buttons on the remote control
to set a time, and press the <ENTER>
button.
9) Press
▲▼
to select [COMMAND].