Panasonic PT-DZ21KU Operating Instructions - Page 97

ENGLISH - 97, To adjust the waveform

Get Panasonic PT-DZ21KU PDF manuals and user guides View all Panasonic PT-DZ21KU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 97 highlights

[DISPLAY OPTION] menu 2) Press ◀▶ to switch [WAVEFORM MONITOR]. zzThe setting will change as follows each time you press the button. [OFF] [ON] 3) Press the button two times to clear. 4) Press ▲▼ to select any horizontal line. zzItems switch as in the following diagram each time the is pressed while the waveform monitor is displayed. "Select line (luminance)" "Select line (red)" "Select line (blue)" "Select line (green)" Note zzThe [FUNCTION BUTTON] ( page 110) can also be used to set. ■■To adjust the waveform Project the luminance adjustment signal of a commercial test disk (0% (0 IRE or 7.5 IRE) - 100% (100 IRE) ) and adjust. Image displayable area Screen position zzLuminance adjustment 1) Select "Select line (luminance)" on the waveform monitor. 2) Adjust black level. zzUse [BRIGHTNESS] in the on-screen menu [PICTURE] to adjust the black level 0% of the image signal to the 0% position of the waveform monitor. 3) Adjust white level. zzUse [CONTRAST] in the on-screen menu [PICTURE] to adjust the white level 100% of the image signal to the 100% position of the waveform monitor. zzRed, green and blue adjustment 1) Set [COLOR TEMPERATURE] to [USER1] or [USER2]. ( page 66) 2) Select "Select line (red)" on the waveform monitor. 3) Adjust dark red areas. zzUse [RED] in [WHITE BALANCE LOW] to adjust the black level 0% of the image signal to the 0% position of the waveform monitor. ( page 66) 4) Adjust bright red areas. zzUse [RED] in [WHITE BALANCE HIGH] to adjust the white level 100% of the image signal to the 100% position of the waveform monitor. ( page 66) 5) Use the procedure for [RED] to adjust [GREEN] and [BLUE]. Note zzBefore adjusting the black level for DVI-D signals, HDMI signals, and SDI signals, confirm that the [DVI SIGNAL LEVEL], [HDMI SIGNAL LEVEL], and [SDI SIGNAL LEVEL] settings are correct. zzWaveform monitor cannot be displayed in [P IN P]. zzThe waveform monitor turns off when [P IN P] is executed during waveform monitoring. zzThe waveform monitor is not displayed when on- screen display is hidden (off). zzTo display the waveform monitor in 3D image, use [3D WAVEFORM MONITOR]. (PT-DZ21KU and PT-DS20KU only) Signal level Settings ENGLISH - 97

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
[DISPLAY OPTION] menu
ENGLISH - 97
Settings
2) Press
◀±
to switch [WAVEFORM
MONITOR].
▶
z
The setting will change as follows each time
you press the button.
[OFF]
[ON]
3) Press the <MENU> button two times to
clear.
4) Press
▲▼
to select any horizontal
line.
▶
z
Items switch as in the following diagram
each time the <ENTER> is pressed while the
waveform monitor is displayed.
“Select line (luminance)”
“Select line (red)”
“Select line (blue)”
“Select line (green)”
Note
z
The [FUNCTION BUTTON] (
page 110) can also be
used to set.
▶
■
To adjust the waveform
Project the luminance adjustment signal of a
commercial test disk (0% (0 IRE or 7.5 IRE) - 100%
(100 IRE) ) and adjust.
Signal level
Image
displayable
area
Screen position
▶
z
Luminance adjustment
1) Select “Select line (luminance)” on the
waveform monitor.
2) Adjust black level.
▶
z
Use [BRIGHTNESS] in the on-screen menu
[PICTURE] to adjust the black level 0% of the
image signal to the 0% position of the waveform
monitor.
3) Adjust white level.
▶
z
Use [CONTRAST] in the on-screen menu
[PICTURE] to adjust the white level 100% of
the image signal to the 100% position of the
waveform monitor.
▶
z
Red, green and blue adjustment
1) Set [COLOR TEMPERATURE] to
[USER1] or [USER2]. (
page 66)
2) Select “Select line (red)” on the
waveform monitor.
3) Adjust dark red areas.
▶
z
Use [RED] in [WHITE BALANCE LOW] to
adjust the black level 0% of the image signal
to the 0% position of the waveform monitor.
(
page 66)
4) Adjust bright red areas.
▶
z
Use [RED] in [WHITE BALANCE HIGH] to
adjust the white level 100% of the image signal
to the 100% position of the waveform monitor.
(
page 66)
5) Use the procedure for [RED] to adjust
[GREEN] and [BLUE].
Note
z
Before adjusting the black level for DVI-D signals,
HDMI signals, and SDI signals, confirm that the [DVI
SIGNAL LEVEL], [HDMI SIGNAL LEVEL], and [SDI
SIGNAL LEVEL] settings are correct.
z
Waveform monitor cannot be displayed in [P IN P].
z
The waveform monitor turns off when [P IN P] is
executed during waveform monitoring.
z
The waveform monitor is not displayed when on-
screen display is hidden (off).
z
To display the waveform monitor in 3D image, use
[3D WAVEFORM MONITOR]. (PT-DZ21KU and
PT-DS20KU only)