Pioneer VSX-1018AH-K Owner's Manual - Page 75

Using other functions, Resetting the system

Get Pioneer VSX-1018AH-K PDF manuals and user guides View all Pioneer VSX-1018AH-K manuals
Add to My Manuals
Save this manual to your list of manuals

Page 75 highlights

Using other functions 11 The front panel display shows each of the following settings for three seconds each: Input source ↓ Surround Back Processing ↓ MCACC preset ↓ ZONE 2 ↓ HDMI Control 2 When you're finished, press STATUS again to switch off the display. Resetting the system Use this procedure to reset all the receiver's settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver into standby. 2 While holding down the front panel STEREO/A.L.C button, press and hold  STANDBY/ON for about two seconds. The display shows RESET?. 3 Press the front panel AUTO SURR/STREAM DIRECT button. The display shows OK. 4 Press SOUND RETRIEVER to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings. • Note that all settings will be saved, even if the receiver is unplugged. Default system settings Setting HDMI Audio HDMI Control Digital Video Conversion Speakers Surround Back System Speaker System Front Center Surr SB SW Crossover X-Curve Default Amp ON ON A Normal SMALL SMALL SMALL SMALLx2 YES 80 Hz OFF Inputs See Input function default and possible settings on page 68. Setting Default MULTI-ZONE Zone 2 Volume Type Variable Zone 2 Volume -60 dB SR+ SR+ Control On/Off OFF SR+ Volume Control On/Off OFF Monitor Out OFF DSP Surround back channel Processing ON Phase Control ON Sound Retriever OFF Sound Delay 0.0 frame Dual Mono CH1 DRC OFF SACD Gain 0 dB LFE Attenuate 0 dB Auto delay OFF Digital Safety OFF Effect Level Extended Stereo 90 Other modes 50 2 PL II Music Options Center Width 3 Dimension 0 Panorama OFF Neo:6 Options Center Image 3 (Neo:6 Music) 10 (Neo:6 Cinema) All Inputs Listening Mode (2 ch) AUTO SURROUND Listening Mode (x ch) AUTO SURROUND Listening Mode (HP) STEREO See also Setting the Audio options on page 71 for other default DSP settings. MCACC MCACC Position Memory M1: MEMORY 1 Channel Level (M1-M6) 0.0 dB Speaker Distance (M1-M6) 10'00'' (10 ft. 00 in.) Standing Wave (M1-M6) ATT SWch Wide Trim 0.0 dB 0.0 dB EQ Data (M1-M6) All channels/bands 0.0 dB EQ Wide Trim 0.0 dB 75 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
Using other functions
11
75
En
The front panel display shows each of the following
settings for three seconds each:
2
When you’re finished, press
STATUS
again to
switch off the display.
Resetting the system
Use this procedure to reset all the receiver’s settings to
the factory default. Use the front panel controls to do this.
1
Switch the receiver into standby.
2
While holding down the front panel
STEREO/A.L.C
button, press and hold
STANDBY/ON
for about two
seconds.
The display shows
RESET?
.
3
Press the front panel
AUTO SURR
/
STREAM DIRECT
button.
The display shows
OK
.
4
Press
SOUND RETRIEVER
to confirm.
OK
appears in the display to indicate that the receiver
has been reset to the factory default settings.
•
Note that all settings will be saved, even if the
receiver is unplugged.
Default system settings
Input source
↓
Surround Back Processing
↓
MCACC preset
↓
ZONE 2
↓
HDMI Control
Setting
Default
HDMI Audio
Amp
HDMI Control
ON
Digital Video Conversion
ON
Speakers
A
Surround Back System
Normal
Speaker System
Front
SMALL
Center
SMALL
Surr
SMALL
SB
SMALLx2
SW
YES
Crossover
80 Hz
X-Curve
OFF
Inputs
See
Input function default and possible settings
on page 68.
MULTI-ZONE
Zone 2 Volume Type
Variable
Zone 2 Volume
–60 dB
SR+
SR+ Control On/Off
OFF
SR+ Volume Control On/Off
OFF
Monitor Out
OFF
DSP
Surround back channel Processing
ON
Phase Control
ON
Sound Retriever
OFF
Sound Delay
0.0 frame
Dual Mono
CH1
DRC
OFF
SACD Gain
0 dB
LFE Attenuate
0 dB
Auto delay
OFF
Digital Safety
OFF
Effect Level
Extended Stereo
90
Other modes
50
2
PL II Music
Options
Center Width
3
Dimension
0
Panorama
OFF
Neo:6 Options
Center Image
3 (Neo:6 Music)
10 (Neo:6
Cinema)
All Inputs
Listening Mode
(2 ch)
AUTO
SURROUND
Listening Mode
(x ch)
AUTO
SURROUND
Listening Mode
(HP)
STEREO
See also
Setting the Audio options
on page 71 for other default
DSP settings.
MCACC
MCACC Position Memory
M1: MEMORY 1
Channel Level (M1–M6)
0.0 dB
Speaker Distance (M1–M6)
10’00’’
(10 ft. 00 in.)
Standing Wave
(M1–M6)
ATT
0.0 dB
SWch Wide Trim
0.0 dB
EQ Data (M1–M6)
All channels/bands
0.0 dB
EQ Wide Trim
0.0 dB
Setting
Default