Sony DSC-RX100M4 Help Guide (Printable PDF) - Page 178

How to reset the user bit, How to select the recording method for the time code TC, Format, How

Get Sony DSC-RX100M4 PDF manuals and user guides View all Sony DSC-RX100M4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 178 highlights

1. MENU → (Setup) → [TC/UB Settings] → [UB Preset], then press in the center of the control wheel. 2. Turn the control wheel and select the first two digits. 3. Set the other digits following the same procedure as in step 2, then press in the center of the control wheel. How to reset the user bit 1. MENU → (Setup) → [TC/UB Settings] → [UB Preset], then press of the control wheel. 2. Press the (Delete) button to reset the user bit (00 00 00 00). in the center How to select the recording method for the time code (TC Format) 1. MENU → (Setup) → [TC/UB Settings] → [TC Format], then press center of the control wheel. in the DF: Records the time code in Drop Frame* format. NDF: Records the time code in Non-Drop Frame format. *The time code is based on 30 frames per second. However, a gap between the actual time and the time code will occur during extended periods of recording as the frame frequency of the NTSC image signal is approximately 29.97 frames per second. Drop frame corrects this gap to make the time code and actual time equal. In drop frame, the first 2 frame numbers are removed every minute except for every tenth minute. The time code without this correction is called non-drop frame. The setting is fixed to [NDF] when recording in 4K/24p, 1080/24p or 1080/25p. How to select the count up format for the time code (TC Run) 1. MENU → (Setup) → [TC/UB Settings] → [TC Run], then press the control wheel. in the center of Rec Run: Sets the stepping mode for the time code to advance only while recording. The time code is recorded sequentially from the last time code of the previous recording. Free Run: Sets the stepping mode for the time code to advance anytime, regardless of the camera operation. The time code may not be recorded sequentially in the following situations even when the time code advances in [Rec Run] mode. When the recording format is changed. When the recording medium is removed.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
  • 232
  • 233
  • 234
  • 235
  • 236
  • 237
  • 238
  • 239
  • 240
  • 241
  • 242
  • 243
  • 244
  • 245
  • 246
  • 247
  • 248
  • 249
  • 250
  • 251
  • 252
  • 253
  • 254
  • 255
  • 256
  • 257
  • 258
  • 259
1.
MENU →
(Setup
) →
[TC/UB Settings]
→
[UB Preset], then press
in the center
of the control wheel.
2. Turn the control wheel and select the first two digits.
3. Set the other digits following the same procedure as in step 2, then press
in the
center of the control wheel.
How to reset the user bit
1.
MENU →
(Setup
) →
[TC/UB Settings]
→
[UB Preset], then press
in the center
of the control wheel.
2. Press the
(Delete) button to reset the user bit (00 00 00 00).
How to select the recording method for the time code (TC
Format)
1.
MENU →
(Setup
) →
[TC/UB Settings]
→
[TC Format], then press
in the
center of the control wheel.
DF:
Records the time code in Drop Frame* format.
NDF:
Records the time code in Non-Drop Frame format.
*
The time code is based on 30 frames per second. However, a gap between the actual time and the
time code will occur during extended periods of recording as the frame frequency of the NTSC image
signal is approximately 29.97 frames per second. Drop frame corrects this gap to make the time code
and actual time equal. In drop frame, the first 2 frame numbers are removed every minute except for
every tenth minute. The time code without this correction is called non-drop frame.
The setting is fixed to [NDF] when recording in 4K/24p, 1080/24p or 1080/25p.
How to select the count up format for the time code (TC Run)
1.
MENU →
(Setup
) →
[TC/UB Settings]
→
[TC Run], then press
in the center of
the control wheel.
Rec Run:
Sets the stepping mode for the time code to advance only while recording. The time code is
recorded sequentially from the last time code of the previous recording.
Free Run:
Sets the stepping mode for the time code to advance anytime, regardless of the camera
operation.
The time code may not be recorded sequentially in the following situations even when the
time code advances in [Rec Run] mode.
When the recording format is changed.
When the recording medium is removed.