Sony XBR-55A9G User Manual - Page 47

Note, Related topics, Pass-through audio formats supported with eARC

Page 47 highlights

(A) (B) (A) AV receiver (B) Speaker cable (not supplied) Use a speaker cable (not supplied) to connect the AV receiver to the CENTER SPEAKER IN terminal of the TV. When connecting, make sure to twist the ends of the speaker cable and insert them into the connection terminals of the TV and AV receiver. The CENTER SPEAKER IN terminal varies depending on the model. Refer to the figures below when connecting the speaker cable. * * *Strip about 10 mm (13/32 inches) of insulation from the speaker cable at each end. Note To prevent the wires of the speaker cable from touching each other, make sure not to strip too much of the speaker cable. Connect the speaker cable properly so that the polarities (+/-) between the TV and AV receiver match. Related topics Connecting an audio system [62] Using the TV with Other Devices | Audio system Pass-through audio formats supported with eARC Confirm that you can pass-through the following audio formats. 7.1 channel linear PCM: 32/44.1/48 kHz 16 bits Dolby Digital Dolby Digital Plus

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89

(A)
(B)
(A)
AV receiver
(B)
Speaker cable (not supplied)
Use a speaker cable (not supplied) to connect the AV receiver to the CENTER SPEAKER IN terminal
of the TV.
When connecting, make sure to twist the ends of the speaker cable and insert them into the connection
terminals of the TV and AV receiver.
The CENTER SPEAKER IN terminal varies depending on the model. Refer to the figures below when
connecting the speaker cable.
*
*
*Strip about 10 mm (13/32 inches) of insulation from the speaker cable at each end.
Note
To prevent the wires of the speaker cable from touching each other, make sure not to strip too
much of the speaker cable.
Connect the speaker cable properly so that the polarities (+/-) between the TV and AV receiver
match.
Related topics
Connecting an audio system
[62] Using the TV with Other Devices | Audio system
Pass-through audio formats supported with eARC
Confirm that you can pass-through the following audio formats.
7.1 channel linear PCM: 32/44.1/48 kHz 16 bits
Dolby Digital
Dolby Digital Plus