TP-Link TD-W8950N TD-W8950N V1 User Guide 1910010940 - Page 36

MAC Clone

Get TP-Link TD-W8950N PDF manuals and user guides View all TP-Link TD-W8950N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 36 highlights

TD-W8950N 150Mbps Wireless N ADSL2+ Modem Router User Guide  Note: ETH and ATM service can not coexist. If the ATM Interface had configured, you cannot configure any other WAN service over the ETH Interface until the ATM Interface is deleted. 4.4.2.6 ETH-PPPoE If your ISP provides a PPPoE connection and you need to use an ETH Interface, follow the steps below to add a WAN service over a selected ETH interface: 1. Add a new ETH interface on the screen of 4.4.1.2 ETH Interface. 2. Click the Add button on the screen Figure 4-7 and the following configuration is similar to PPPoE over ATM interface (see section 4.4.2.1 ATM-EoA-PPPoE). 4.4.2.7 ETH-IPoE If your ISP provides an IPoE connection and you want to use an ETH Interface, follow the steps below to add a WAN service over a selected ETH interface: 1. Add a new ETH interface on the screen of 4.4.1.2 ETH Interface. 2. Click the Add button on the screen Figure 4-7 and the next configuration is similar to IPoE over ATM interface (see section 4.4.2.2 ATM-EoA-IPoE). 4.4.2.8 ETH-Bridge If you want to adopt the Bridge service and you need to use an ETH Interface, follow the steps below to add a WAN service over a selected ETH interface: 1. Add a new ETH interface on the screen of 4.4.1.2 ETH Interface. 2. Click the Add button on the screen Figure 4-7 and the next configuration is similar to Bridge over ATM interface (see section 4.4.2.3 ATM-EoA-Bridg). 4.4.3 MAC Clone Choose menu "Advanced Setup""MAC Clone", you can configure the MAC address of the WAN Interface as shown below. The WAN Interface List displays the Lay2 Interfaces you have configured on the section 4.4.1 Layer2 Interface and its default MAC Address. If you have not configured corresponding WAN Service for the interface on the section 4.4.2 WAN Service, the blank for MAC Address will display "Need a corresponding WAN Service". The last one of WAN Interface List displays your PC's current address. Figure 4-20 Type the new value for the WAN Interface who's MAC Address you want to change. 28

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
TD-W8950N
150Mbps Wireless N ADSL2+ Modem Router User Guide
Note:
ETH and ATM service can not coexist. If the ATM Interface had configured, you cannot configure
any other WAN service over the ETH Interface until the ATM Interface is deleted.
4.4.2.6 ETH-PPPoE
If your ISP provides a
PPPoE
connection and you need to use an
ETH
Interface, follow the steps
below to add a WAN service over a selected ETH interface:
1.
Add a new
ETH
interface on the screen of
4.4.1.2
ETH Interface
.
2.
Click the
Add
button on the screen Figure 4-7 and the following configuration is similar to
PPPoE
over ATM interface
(see section
4.4.2.1
ATM-EoA-PPPoE
).
4.4.2.7 ETH-IPoE
If your ISP provides an
IPoE
connection and you want to use an
ETH
Interface, follow the steps
below to add a WAN service over a selected ETH interface:
1.
Add a new
ETH
interface on the screen of
4.4.1.2
ETH Interface
.
2.
Click the
Add
button on the screen Figure 4-7 and the next configuration is similar to
IPoE
over ATM interface
(see section
4.4.2.2
ATM-EoA-IPoE
).
4.4.2.8 ETH-Bridge
If you want to adopt the
Bridge
service and you need to use an
ETH
Interface, follow the steps
below to add a WAN service over a selected ETH interface:
1.
Add a new
ETH
interface on the screen of
4.4.1.2
ETH Interface
.
2.
Click the
Add
button on the screen Figure 4-7 and the next configuration is similar to
Bridge
over ATM interface
(see section
4.4.2.3
ATM-EoA-Bridg
).
4.4.3
MAC Clone
Choose menu “
Advanced Setup
”
“
MAC Clone
”, you can configure the MAC address of the
WAN Interface as shown below.
The WAN Interface List displays the Lay2 Interfaces you have configured on the section
4.4.1
Layer2 Interface
and its default MAC Address. If you have not configured corresponding WAN
Service for the interface on the section
4.4.2
WAN Service
, the blank for MAC Address will display
“Need a corresponding WAN Service”.
The last one of WAN Interface List displays your PC’s current address.
Figure 4-20
Type the new value for the WAN Interface who’s MAC Address you want to change.
28