Yamaha DTX700 Reference Manual - Page 30
KIT/PAD
View all Yamaha DTX700 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 30 highlights
KIT Settings: off, snares, tuning, tempo, filter, snaresOn/Off NOTE • The initial default setting of the PadCtrlType (Pad Control Type) parameter depends on the drum kit selected. • The settings available for the PadCtrlType (Pad Control Type) parameter depend on the trigger input jack that the pad has been plugged into. For example, the settings "snares" and "snaresOn/Off" are available only when the [qSNARE] trigger input jack is being used. KIT/PAD 2/3 Hi-hat MIDI Type (HH MIDI Type) If "MIDI" has been set for the HH Func (Hi-hat Function) parameter (also from the Menu area's Kit/Pad page), use this parameter to set the type of MIDI messages generated by the hi-hat controller. Settings: CC01 to CC95 (Control Change), AT (Aftertouch), PBup (Pitch Bend up), PBdwn (Pitch Bend down) NOTE • If "hi-hat" has been set for the HH Func (Hi-hat Function) parameter (also from the Menu area's Kit/Pad page), this setting will be displayed as "-----" and modification will not be possible. KIT/PAD 3/3 Hi-hat Function (HH Func) Use this parameter to specify how a hi-hat controller connected to the [HI-HAT CONTROL] trigger-input jack is to function. hi-hat MIDI The hi-hat controller will function in the standard way for playing the hi-hat cymbal. When you step on the hi-hat controller, a MIDI message is output in line with the settings of the HH MIDI Ch (Hi-hat MIDI Channel) and HH MIDI Type (Hi-hat MIDI Type) parameters below. Settings: hi-hat, MIDI NOTE • When this parameter is set to "hi-hat" and "on" has been selected for the SendHH (Send Hi-hat Controller) parameter from the Menu area's Utility/MIDI page, Control Change 4 messages corresponding to the degree to which the hi-hat controller is depressed will be sent to external MIDI devices on MIDI channel 10. • When this parameter is set to "MIDI", MIDI messages are sent regardless of the setting of the SendHH (Send Hi-hat Controller) parameter from the Menu area's Utility/MIDI page. Hi-hat MIDI Channel (HH MIDI Ch) If "MIDI" has been set for the HH Func (Hi-hat Function) parameter (also from the Menu area's Kit/Pad page), use this parameter to set the MIDI channel for output of the MIDI messages generated by the hi-hat controller. Settings: 1 to 16 NOTE • If "hi-hat" has been set for the HH Func (Hi-hat Function) parameter (also from the Menu area's Kit/Pad page), this setting will be displayed as "--" and modification will not be possible. Snare Wire On/Off (SnaresOn/Off) Use this parameter to control the behavior of the pad connected to the [qSNARE] trigger input jack. If set to "on", the voices assigned to the SnareHd, SnareOp, and SnareCl pads will be output. If set to "off", meanwhile, the voices assigned to the SnrHdOff, SnrOpOff, and SnrClOff pads will be output. For more details, refer to page 3. Settings: off, on Snare Wire Adjustment (SnaresAdjust) Use this parameter to adjust the tightness of the snare wire. Higher values correspond to tighter snare wires and vice-versa. Settings: 1 to 15 NOTE • When you adjust this parameter, the Decay parameter* from the Menu area's Kit/Voice page also changes. (*: Applies only when the VoiceCategory parameter has been set to "SnareHd" or "SnareOp".) SnareBuzz Use this parameter to specify how the snare wire effect resonates with kick and tom sounds. The higher the setting, the greater the degree of resonance. Set to "off" to prevent the snare wire from resonating. Settings: off, 1 to 5 DTX700 Reference Manual 30