Home » ZyXEL Manuals » Networking » ZyXEL GS-1548 » Manual Viewer

ZyXEL GS-1548 User Guide - Page 148

Table 72, Feature, Description

Get ZyXEL GS-1548 PDF manuals and user guides

Add to My Manuals
Save this manual to your list of manuals

Page 148 highlights

Chapter 22 Product Specifications This section describes the general software features of the Switch. Table 72 Firmware Features FEATURE DESCRIPTION VLAN A VLAN (Virtual Local Area Network) allows a physical network to be partitioned into multiple logical networks. Devices on a logical network belong to one group. A device can belong to more than one group. With VLAN, a device cannot directly talk to or hear from devices that are not in the same group(s); the traffic must first go through a router. Layer 2 Management Forward traffic based on the destination MAC address and VLAN group (ID). QoS Queuing is used to help solve performance degradation when there is network congestion. Two scheduling services are supported: Strict Priority (SP) and Weighted Round Robin (WRR). This allows the Switch to maintain separate queues for packets from each individual source or flow and prevent a source from monopolizing the bandwidth. Rate Control Rate control is a combination of bandwidth management and broadcast storm control. This feature allows you to set limits for incoming and outgoing traffic on the ports. The broadcast storm control feature helps prevent broadcast, multicast or unknown unicast traffic from flooding your network. Port Mirroring Port mirroring allows you to copy traffic going from one or all ports to another or all ports in order that you can examine the traffic from the mirror port (the port you copy the traffic to) without interference. Link Aggregation Link aggregation (trunking) is the grouping of physical ports into one logical higher-capacity link. You may want to trunk ports if for example, it is cheaper to use multiple lower-speed links than to under-utilize a high-speed, but more costly, single-port link. Device Management Use the web configurator to easily configure the rich range of features on the Switch. Firmware Upgrade Download new firmware (when available) from the ZyXEL web site and use the web configurator to put it on the Switch. Configuration Backup & Restoration Auto DoS Auto VoIP Dynamic ARP Note: Only upload firmware for your specific model! Make a copy of the Switch's configuration and put it back on the Switch later if you decide you want to revert back to an earlier configuration. The Automatic Denial of Service (DoS) attack detection and prevention feature helps protect you from hackers trying to disrupt or shut down your network. The Automatic VoIP feature grants the highest priority to VoIP traffic ensuring better sound quality and reliability for end users. Dynamic ARP allows you to filter incoming traffic based on the MAC to IP address mapping. The Switch can be configured to only allow trusted devices to communicate via its ports. 148 GS-1524/GS-1548 User's Guide

Section	Page
GS-1524 / GS-1548	1
About This User's Guide	3
Document Conventions	5
Safety Warnings	7
Contents Overview	9
Table of Contents	11
Introduction and Hardware Overview	17
Getting to Know Your Switch	19
1.1 Introduction	19
1.1.1 Backbone Application	19
1.1.2 Bridging Example	20
1.1.3 High Performance Switching Example	21
1.1.4 IEEE 802.1Q VLAN Application Examples	21
Hardware Installation and Connection	23
2.1 Freestanding Installation	23
2.2 Mounting the Switch on a Rack	24
2.2.1 Rack-mounted Installation Requirements	24
2.2.2 Attaching the Mounting Brackets to the Switch	24
2.2.3 Mounting the Switch on a Rack	25
Hardware Overview	27
3.1 Front Panel	27
3.1.1 Ethernet Ports	28
3.1.2 Mini-GBIC Slots	28
3.2 The RESET Button	30
3.3 LEDs	30
3.4 Rear Panel	31
3.4.1 Power Connector	32
Basic & Advanced Settings	33
The Web Configurator	35
4.1 Introduction	35
4.2 System Login	35
4.3 The Status Screen	36
4.3.1 The LED Panel	37
4.3.2 The Navigation Panel	37
4.3.3 Change Your Password	39
4.4 Saving Your Configuration	39
4.5 Switch Lockout	40
4.6 Resetting the Switch	40
4.7 Logging Out of the Web Configurator	41
4.8 Help	41
System	43
5.1 System Screen	43
5.1.1 Configure IP Address	44
5.1.2 Layer 2 (L2) Table Aging	45
5.1.3 Backup Settings	45
5.1.4 Restore Settings	46
5.2 System: Change Password	47
5.3 Firmware Upgrade	47
5.3.1 System: Restart/Reset	48
Port Settings	49
6.1 Port Status	49
6.2 Port Configuration	50
System and Port Statistics	53
7.1 Overview	53
7.2 Statistics Summary	53
7.3 Port Statistics	54
VLAN	57
8.1 Introduction to IEEE 802.1Q Tagged VLANs	57
8.1.1 Forwarding Tagged and Untagged Frames	57
8.2 Static VLAN	58
8.2.1 IEEE 802.1Q VLAN Screen	58
8.2.2 Create IEEE 802.1Q VLAN Screen	59
8.2.3 Edit IEEE 802.1Q VLAN Screen	60
Trunking	63
9.1 Trunking Overview	63
9.1.1 Distribution Criteria	63
9.2 Trunk Setting Screen	64
Mirroring	65
10.1 Port Mirroring Settings	65
QoS	67
11.1 QoS Overview	67
11.1.1 Weighted Round Robin (WRR)	67
11.1.2 Strict Priority	68
11.2 QoS Enhancement	68
11.3 Configuring QoS	69
11.3.1 Change Number of Queues	70
11.4 Advanced QoS Settings	70
11.4.1 Port Based QoS	71
11.4.2 DSCP Based QoS	72
11.4.3 Differentiated Services Code Point (DSCP) Overview	72
11.4.4 DSCP Based QoS Screen	73
11.4.5 ToS Based QoS	74
11.4.6 IP Address Based QoS	75
Port Rate Limit and Storm Control	77
12.1 Port Rate Screen	77
12.1.1 Rate Limit Screen	78
12.1.2 Broadcast Storm Control Setup	79
Layer 2 (L2) Management	83
13.1 Configuring L2 Management	83
13.1.1 Add a Static MAC Address Entry	84
13.2 Viewing the L2 Address Table	85
Cable Diagnostics	87
14.1 Diagnostics Overview	87
Auto Denial of Service (DoS)	89
15.1 About Denial of Service Attacks	89
15.1.1 DoS Attacks Summary	89
15.2 Global Auto DoS Attack Prevention	90
15.3 Advanced Auto DoS Attack Prevention	91
Auto VoIP	93
16.1 About Auto VoIP	93
16.2 Auto VoIP Settings	94
Management and Troubleshooting	95
Event Logging	97
17.1 Event Logging Overview	97
17.2 Logging Screen	98
17.3 Logging: Add Server	99
17.4 Viewing RAM and Flash Logs	99
17.5 Searching RAM and Flash Logs	102
17.5.1 Search Results	103
SNMP	105
18.1 About SNMP	105
18.1.1 Supported MIBs	106
18.1.2 SNMP Traps	107
18.1.3 SNMP v3 and Authentication	107
18.1.4 SNMP EngineID	107
18.2 SNMP Group	108
18.2.1 SNMP Group: Create	109
18.2.2 SNMP Group: Modify	110
18.3 SNMP User	110
18.3.1 SNMP User: Create	112
18.3.2 SNMP User: Modify	113
18.4 SNMP Community	114
18.4.1 SNMP Community: Create	115
18.4.2 SNMP Community: Modify	116
18.5 SNMP Notification	116
18.6 SNMP Trap Station	117
18.6.1 SNMP Trap Station: Create	119
18.6.2 SNMP Trap Station: Modify	119
RMON-Lite	121
19.1 RMON-Lite Overview	121
19.2 RMON Statistics: Overview	122
19.3 RMON-Lite Statistics: Port	123
19.4 RMON-Lite History MIB	124
19.4.1 RMON History Control: Overview	125
19.4.2 RMON History Control: Modify	126
19.4.3 RMON History Statistics: Overview	127
19.4.4 RMON History Statistics: Control	128
19.5 RMON Alarm: Overview	129
19.5.1 RMON Alarm: Create New Alarm	130
19.6 RMON Event: Overview	132
19.6.1 RMON Event: Create New Event	133
19.7 RMON Event Log: Overview	134
19.7.1 RMON Event Log: Event	135
Dynamic ARP	137
20.1 ARP Table Overview	137
20.1.1 ARP Table Entries	137
20.1.2 How Dynamic ARP Works	137
20.2 Enabling Dynamic ARP	138
20.3 Viewing ARP Table Entries	139
20.4 Adding ARP Table Entries	140
Troubleshooting	141
21.1 Power, Hardware Connections, and LEDs	141
21.2 Switch Access and Login	142
Product Specifications	145
22.1 General Switch Specifications	145
Appendices and Index	151
IP Addresses and Subnetting	153
Legal Information	163

Match case Limit results 1 per page

Chapter 22 Product Specifications

GS-1524/GS-1548 User’s Guide

148

This section describes the general software features of the Switch.

Table 72

Firmware Features

FEATURE

DESCRIPTION

VLAN

A VLAN (Virtual Local Area Network) allows a physical network

to be partitioned into multiple logical networks. Devices on a

logical network belong to one group. A device can belong to

more than one group. With VLAN, a device cannot directly talk

to or hear from devices that are not in the same group(s); the

traffic must first go through a router.

Layer 2 Management

Forward traffic based on the destination MAC address and VLAN

group (ID).

QoS

Queuing is used to help solve performance degradation when

there is network congestion. Two scheduling services are

supported: Strict Priority (SP) and Weighted Round Robin

(WRR). This allows the Switch to maintain separate queues for

packets from each individual source or flow and prevent a

source from monopolizing the bandwidth.

Rate Control

Rate control is a combination of bandwidth management and

broadcast storm control. This feature allows you to set limits

for incoming and outgoing traffic on the ports. The broadcast

storm control feature helps prevent broadcast, multicast or

unknown unicast traffic from flooding your network.

Port Mirroring

Port mirroring allows you to copy traffic going from one or all

ports to another or all ports in order that you can examine the

traffic from the mirror port (the port you copy the traffic to)

without interference.

Link Aggregation

Link aggregation (trunking) is the grouping of physical ports

into one logical higher-capacity link. You may want to trunk

ports if for example, it is cheaper to use multiple lower-speed

links than to under-utilize a high-speed, but more costly,

single-port link.

Device Management

Use the web configurator to easily configure the rich range of

features on the Switch.

Firmware Upgrade

Download new firmware (when available) from the ZyXEL web

site and use the web configurator to put it on the Switch.

Note: Only upload firmware for your specific model!

Configuration Backup &

Restoration

Make a copy of the Switch’s configuration and put it back on

the Switch later if you decide you want to revert back to an

earl

er configuration.

Auto DoS

The Automatic Denial of Service (DoS) attack detection and

prevention feature helps protect you from hackers trying to

disrupt or shut down your network.

Auto VoIP

The Automatic VoIP feature grants the highest priority to VoIP

traffic ensuring better sound quality and reliability for end

users.

Dynamic ARP

Dynamic ARP allows you to filter incoming traffic based on the

MAC to IP address mapping. The Switch can be configured to

only allow trusted devices to communicate via its ports.