ZyXEL GS1910-24 User Guide - Page 31

Factory Defaults, Restart Device - factory reset

Get ZyXEL GS1910-24 PDF manuals and user guides View all ZyXEL GS1910-24 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Chapter 4 The Web Configurator Table 4 Navigation Panel Links (continued) LINK MLD Snooping LLDP Neighbours LLDP-MED Neighbours EEE Port Statistics MAC Table VLANs VLAN Membership VLAN Port Stack VCL MAC-based VLAN sFlow sFlow Statistics Diagnostic Ping Ping6 VeriPHY DESCRIPTION This link takes you to a screen where you can view MLD snooping status, MLD group information and SFM (Source-Filtered Multicast) information.. This link takes you to a screen where you can view the LLDP neighboring device information. This link takes you to a screen where you can view the LLDP-MED neighboring device information. This link takes you to a screen where you can view the EEE information exchanged via LLDP. This link takes you to a screen where you can view LLDP traffic statistics on the Switch or on a port. This link takes you to a screen where you can view the MAC address and VLAN ID of a device attached to a port. You can also view what kind of MAC address it is. This link takes you to a screen where you can view status of the VLAN group. This link takes you to a screen where you can view detailed VLAN settings on a port. This link takes you to a screen where you can see whether stacking is enabled on the Switch. This link takes you to a screen where you can view the MAC-based VLAN settings. This link takes you to a screen where you can view sFlow receiver state and sFlow packet statistics on each port. This link takes you to a screen where you can ping IPv4 addresses to test connections. This link takes you to a screen where you can ping IPv6 addresses to test connections. This link takes you to a screen where you can perform a physical wire-pair test of the Ethernet connections on the specified port(s). Maintenance Restart Device Factory Defaults Software Upload Image Select VeriPHY® cable diagnostics provide extensive network cable information such as cable length, termination status, and open/short fault location. This link takes you to a screen where you can reboot the system without turning the power off. This link takes you to a screen where you can to reset the Switch back to the factory defaults. This link takes you to a screen where you can upload firmware to the Switch. This link takes you to a screen where you can switch to use a second firmware image if available. Configuration Backup Upload This screen is not available on the XGS1910-24 or XGS1910-48. This link takes you to a screen where you can back up your current Switch configuration to a computer. This link takes you to a screen where you can restore a previously saved configuration from your computer to the Switch. GS1910/XGS1910 Series User's Guide 31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Chapter 4 The Web Configurator
GS1910/XGS1910 Series User’s Guide
31
MLD Snooping
This link takes you to a screen where you can view MLD snooping status, MLD group
information and SFM (Source-Filtered Multicast) information..
LLDP
Neighbours
This link takes you to a screen where you can view the LLDP neighboring device
information.
LLDP-MED
Neighbours
This link takes you to a screen where you can view the LLDP-MED neighboring device
information.
EEE
This link takes you to a screen where you can view the EEE information exchanged via
LLDP.
Port Statistics
This link takes you to a screen where you can view LLDP traffic statistics on the Switch or
on a port.
MAC Table
This link takes you to a screen where you can view the MAC address and VLAN ID of a
device attached to a port. You can also view what kind of MAC address it is.
VLANs
VLAN
Membership
This link takes you to a screen where you can view status of the VLAN group.
VLAN Port
This link takes you to a screen where you can view detailed VLAN settings on a port.
Stack
This link takes you to a screen where you can see whether stacking is enabled on the
Switch.
VCL
MAC-based
VLAN
This link takes you to a screen where you can view the MAC-based VLAN settings.
sFlow
sFlow Statistics
This link takes you to a screen where you can view sFlow receiver state and sFlow packet
statistics on each port.
Diagnostic
Ping
This link takes you to a screen where you can ping IPv4 addresses to test connections.
Ping6
This link takes you to a screen where you can ping IPv6 addresses to test connections.
VeriPHY
This link takes you to a screen where you can perform a physical wire-pair test of the
Ethernet connections on the specified port(s).
VeriPHY® cable diagnostics provide extensive network cable information such as cable
length, termination status, and open/short fault location.
Maintenance
Restart Device
This link takes you to a screen where you can reboot the system without turning the
power off.
Factory Defaults
This link takes you to a screen where you can to reset the Switch back to the factory
defaults.
Software
Upload
This link takes you to a screen where you can upload firmware to the Switch.
Image Select
This link takes you to a screen where you can switch to use a second firmware image if
available.
This screen is not available on the XGS1910-24 or XGS1910-48.
Configuration
Backup
This link takes you to a screen where you can back up your current Switch configuration
to a computer.
Upload
This link takes you to a screen where you can restore a previously saved configuration
from your computer to the Switch.
Table 4
Navigation Panel Links
(continued)
LINK
DESCRIPTION