Dell PowerVault 130T DLT Service Manual - Page 33

The library Operator Panel displays, The PC displays

Get Dell PowerVault 130T DLT PDF manuals and user guides View all Dell PowerVault 130T DLT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

PowerVault 130T Service Manual Important Procedures WARNING: Do not power down or reset the library while in the writing mode. 6. When the library Operator Panel displays Write OK..., push the Reset button on the operator panel. 7. The library will reboot and the operator panel will display: BOOT RE-FLASH APPLICATION RUNNING Connect CSE Port... 8. At the DOS prompt, type flash97.exe boot.prm The program will then prompt you for the serial port number. Type in the serial port number that is connected to the cable and press ENTER. The PC displays Sending and the library Operator Panel displays Receiving. Next, the PC displays Send Status: File transfer completed successfully. The library Operator Panel displays Writing.... . WARNING: Do not power down or reset the library while in the writing mode. 9. When the library Operator Panel displays Write OK..., push the Reset button on the operator panel. 10. During boot, while the library display reads Available (visible for about five seconds), press the MENU button on the operator panel. 11. The operator panel displays the choices >Functional Reflash NVRAM test & init Select Functional Reflash using the arrow buttons and press ENTER The operator panel displays Connect CSE port... 12. At the DOS prompt, type flash97.exe release.prm The program will then prompt you for the serial port number. Type in the serial port number that is connected to the cable and press ENTER. The PC displays Sending and the library Operator Panel displays Receiving Next, the PC displays Send Status: File transfer completed successfully. The library Operator Panel displays Writing..... WARNING: Do not power down or reset the library while in the writing mode. 4473D 2-11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
PowerVault 130T Service Manual
Important Procedures
4473D
2–11
WARNING:
Do not power down or reset the library while in the writing
mode.
6.
When the library Operator Panel displays
Write OK...<Reset>
, push the
Reset
button on the operator panel.
7.
The library will reboot and the operator panel will display:
BOOT RE–FLASH
APPLICATION RUNNING
Connect CSE Port
...
8.
At the DOS prompt, type
flash97.exe boot.prm
The program will then prompt you for the serial port number.
Type in the
serial port number that is connected to the cable and press ENTER.
The PC displays
Sending
and the library Operator Panel displays
Receiving
.
Next, the PC displays
Send Status: File transfer completed
successfully
.
The library Operator Panel displays
Writing
....
.
WARNING:
Do not power down or reset the library while in the writing
mode.
9.
When the library Operator Panel displays
Write
OK
...
<Reset>
, push the
Reset button on the operator panel.
10. During boot, while the library display reads
<Menu> Available
(visible
for about five seconds), press the MENU button on the operator panel.
11. The operator panel displays the choices
>Functional Reflash
NVRAM test & init
Select
Functional Reflash
using the arrow buttons and press ENTER
The operator panel displays
Connect CSE port
...
12. At the DOS prompt, type
flash97.exe release.prm
The program will then prompt you for the serial port number.
Type in the
serial port number that is connected to the cable and press ENTER.
The PC displays
Sending
and the library Operator Panel displays
Receiving
Next, the PC displays
Send Status: File transfer completed
successfully
.
The library Operator Panel displays
Writing
.....
WARNING:
Do not power down or reset the library while in the writing
mode.