Dell PowerVault 130T DLT Service Manual - Page 63

column assembly., Carefully raise the hand to the top of the Z

Get Dell PowerVault 130T DLT PDF manuals and user guides View all Dell PowerVault 130T DLT manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

PowerVault 130T Service Manual 8. Remove the screw holding the CYH card cover using a Torx driver. 9. Move the cover horizontally until its front and side flanges are disengaged from the CYH card, and remove the cover. 10. Note the routing of the cables for replacement. 11. Flip up one side of the cable clamp located under the hand and release the cable. 12. Disconnect cables from the J3, J20, and J18 connectors on the CYH card. 13. Rotate the robot clockwise so the hand is inside the library. 14. Carefully raise the hand to the top of the Z column assembly. 15. Remove the two screws securing the flex cable clamp bracket to the bottom of the hand using a Torx driver with a T-10 bit. 16. Lay the cable on the library floor, making sure it does not interfere with Z column movement. Hand/Camera Assembly 4473D 3-27

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
PowerVault 130T Service Manual
Hand/Camera Assembly
4473D
3–27
8.
Remove the screw holding the CYH card
cover using a Torx driver.
9.
Move the cover horizontally until its front
and side flanges are disengaged from the
CYH card, and remove the cover.
10. Note the routing of the cables for
replacement.
11. Flip up one side of the cable clamp located
under the hand and release the cable.
12. Disconnect cables from the J3, J20, and J18
connectors on the CYH card.
13. Rotate the robot clockwise so the hand is
inside the library.
14. Carefully raise the hand to the top of the Z
column assembly.
15. Remove the two screws securing the flex
cable clamp bracket to the bottom of the
hand using a Torx driver with a T-10 bit.
16.Lay the cable on the library floor, making
sure it does not interfere with Z column
movement.