HP Designjet 350c HP Designjet 330 and 350C Plotters - Users Guide - Page 22
shown below.
 |
View all HP Designjet 350c manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 22 highlights
Setting up your plotter Task 3: Position the plotter Task 3: Position the plotter If you have fitted the optional roll-feed kit, you must also fit the legs assembly for stability, so this task does not apply. If you have not fitted the optional roll-feed and legs kit, position the plotter as shown below. For operating temperature and humidity, see page 10-5. Allow enough space above the plotter to open the cover. If the plotter is without legs ... Level surface. Sturdy support. For plotter weights, see page 10-4. Leave enough space for your largest sheet size to hang freely from the media exit slot without touching the ground. 1-8 1739 Place the plotter at the edge of the support, so that sheets exit without hitting the top of the support.
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17 -
18 -
19 -
20 -
21 -
22 -
23 -
24 -
25 -
26 -
27 -
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
 |
 |
1–8
Task 3: Position the plotter
If you have fitted the optional roll-feed kit, you must also fit the legs assembly
for stability, so this task does not apply.
If you have not fitted the optional roll-feed and legs kit,
position the plotter as
shown below.
For operating temperature and humidity, see page 10–5.
Allow enough space above the plotter to open the cover.
Level surface.
Sturdy support.
For plotter
weights, see page 10–4.
Place the plotter at the edge of
the support, so that sheets exit
without hitting the top of the
support.
Leave enough space for your largest sheet size
to hang freely from the media exit slot without
touching the ground.
If the plotter is without legs ...
1739
Setting up your plotter
Task 3: Position the plotter