HP StorageWorks 2/16V HP StorageWorks Fabric OS V3.1.3A Release Notes (AA-RUQY - Page 64

FABRIC-RECONFIG, Recommended Action, Severity, Probable Cause

Get HP StorageWorks 2/16V - SAN Switch PDF manuals and user guides View all HP StorageWorks 2/16V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 64 highlights

New Diagnostic and System Error Messages Recommended Action For the SAN Switch 2/16, replace the motherboard FRU. For the SAN Switch 2/8, you must replace the entire switch. Severity Critical FABRIC-RECONFIG Message Switch: , Info FABRIC-RECONFIG, 4, fabric: Probable Cause The fabric has reconfigured due to an offline port. The reason can be one of the following: ■ Fabric Merge: Merging two fabrics. ■ Own ID Rcvd: A subordinate switch receives an EFP or EFP ACC that has a payload error, listing this switch as being the principal switch. ■ Fabric Segment: Principal port became segmented. ■ Offline: Principal port went offline. ■ Unconfirmed domain: Switch was not able to get a domain ID. RDI ACC was never received. ■ Rcv BF: Received Build Fabric (BF) command. ■ HA: At F2 State: According to the Fibre Channel Specification, F2 is defined as the principal switch selection. If a failover occurs at this time, the switch is forced to restart principal switch selection. ■ HA: No Upstream: After failover, the newly active fabric thinks it is subordinate, but there is no upstream. ■ HA: bad EFP resp: Received an invalid EFP response. ■ HA: RJT EFP resp: Received an EFP reject response in which this EFP was used for verifying the neighbor's domain list as part of fabric warm-start recovery. A reject occurs if the neighbor is reconfiguring or the neighbor's port is in a bad state. 64 Fabric OS 3.1.3a Release Notes

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
New Diagnostic and System Error Messages
64
Fabric OS 3.1.3a Release Notes
Recommended Action
For the SAN Switch 2/16, replace the motherboard FRU.
For the SAN Switch 2/8, you must replace the entire switch.
Severity
Critical
Message
Switch: <number>, Info FABRIC-RECONFIG, 4, fabric: <reason>
Probable Cause
The fabric has reconfigured due to an offline port. The reason can be one of the
following:
■
Fabric Merge: Merging two fabrics.
■
Own ID Rcvd: A subordinate switch receives an EFP or EFP ACC that has a
payload error, listing this switch as being the principal switch.
■
Fabric Segment: Principal port became segmented.
■
Offline: Principal port went offline.
■
Unconfirmed domain: Switch was not able to get a domain ID. RDI ACC was
never received.
■
Rcv BF: Received Build Fabric (BF) command.
■
HA: At F2 State: According to the Fibre Channel Specification, F2 is defined
as the principal switch selection. If a failover occurs at this time, the switch is
forced to restart principal switch selection.
■
HA: No Upstream: After failover, the newly active fabric thinks it is
subordinate, but there is no upstream.
■
HA: bad EFP resp: Received an invalid EFP response.
■
HA: RJT EFP resp: Received an EFP reject response in which this EFP was
used for verifying the neighbor's domain list as part of fabric warm-start
recovery. A reject occurs if the neighbor is reconfiguring or the neighbor's
port is in a bad state.
FABRIC-RECONFIG