HP rp5400 User Guide - HP rp5400 Family of Servers - Page 144

Stand-alone Server Cover Replacement

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 144 highlights

Removing and Replacing Components Individual Component Remove/Replace Instructions Stand-alone Server Cover Replacement The rp54xx server can be ordered as a stand-alone unit. In this configuration, the server has a one-piece protective cover over it and sits on a platform with locking wheels attached. To place the server on its wheeled platform, perform the following procedure: WARNING The stand-alone server weights 69 kg (l50 lbs). Placing the stand-alone server on its platform requires three people or a suitable lifting device. Failure to heed this precaution can result in serious personal injury or destruction of the server. 1. Lift the platform and turn both of the spring-loaded, flat-headed pins (item 1) a quarter turn to the right to lock them out of the way before placing the server on the platform. 2. Using a lifting devise or a minimum of three people, lift the server onto the platform. Align the server and platform so that the pins will lock. 3. Reach under the platform, locate the spring-loaded, flat headed pins and turn them one quarter turn to the left to unlock them. Gently slide the server around on the platform until the spring-loaded flat-head pins snap into their holes. 4. Once again, reach under the platform on the right side and fasten both front and back knurl-knobbed, spring-loaded pins (item 2). 2 1 To place the cover on a stand-alone server, perform the following procedures: 1. Set the protective cover on the server and align the holes located near the bottom edge of both sides of the server cover. 2. Fasten the screws (with captive washers) through the cover, into the platform. The following graphic shows the protective cover. 130 Chapter 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
Chapter 7
Removing and Replacing Components
Individual Component Remove/Replace Instructions
130
Stand-alone Server Cover Replacement
The rp54xx server can be ordered as a stand-alone unit. In this configuration, the server has a one-piece
protective cover over it and sits on a platform with locking wheels attached.
To place the server on its wheeled platform, perform the following procedure:
WARNING
The stand-alone server weights 69 kg (l50 lbs). Placing the stand-alone server on its
platform requires three people or a suitable lifting device. Failure to heed this
precaution can result in serious personal injury or destruction of the server.
1. Lift the platform and turn both of the spring-loaded, flat-headed pins (item 1) a quarter turn to the right
to lock them out of the way before placing the server on the platform.
2. Using a lifting devise or a minimum of three people, lift the server onto the platform. Align the server and
platform so that the pins will lock.
3. Reach under the platform, locate the spring-loaded, flat headed pins and turn them one quarter turn to
the left to unlock them. Gently slide the server around on the platform until the spring-loaded flat-head
pins snap into their holes.
4. Once again, reach under the platform on the right side and fasten both front and back knurl-knobbed,
spring-loaded pins (item 2).
To place the cover on a stand-alone server, perform the following procedures:
1. Set the protective cover on the server and align the holes located near the bottom edge of both sides of the
server cover.
2. Fasten the screws (with captive washers) through the cover, into the platform.
The following graphic shows the protective cover.
1
2