HP rp5400 User Guide - HP rp5400 Family of Servers - Page 53

install or service: CPUs, Memory, PSMs, the Platform Monitor or PCI I/O cards, Step 3.

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Installing Additional Components Installing Graphics NOTE DC voltages are present when the server is connected to AC power. Do not attempt to install or service: CPUs, Memory, PSMs, the Platform Monitor or PCI I/O cards installed in non-Turbo slots (1-6) while DC voltage is present. Failure to observe this warning may result in damage to the server. Step 3. Make the right side of the server accessible for service. Step 4. Using a Torx 15 screwdriver, loosen the captive screws on the right side panel. This panel has a label which shows which PCI I/O slots are available and the corresponding paths. The label shown below is for an rp5400. Chapter 3 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
Chapter 3
Installing Additional Components
Installing Graphics
39
NOTE
DC voltages are present when the server is connected to AC power. Do not attempt to
install or service: CPUs, Memory, PSMs, the Platform Monitor or PCI I/O cards
installed in non-Turbo slots (1-6) while DC voltage is present. Failure to observe this
warning may result in damage to the server.
Step 3.
Make the right side of the server accessible for service.
Step 4.
Using a Torx 15 screwdriver, loosen the captive screws on the right side panel. This panel has a
label which shows which PCI I/O slots are available and the corresponding paths. The label shown
below is for an rp5400.