HP rp5400 User Guide - HP rp5400 Family of Servers - Page 31

Step 12., Pins in Slots

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

Server Unpacking and Installation Install Stand-Alone Server in a Cabinet Step 12. Take the tray and place it onto the pins that extend from the slides' inner members. The slots with wide lead-in guides on the side of the tray fit down onto the slides' pins. The flat part of the tray will be on top, and the mounting holes in the top of the tray will be located to the right of the center of the tray. Slide the tray all the way down on both sides so that the pins reach the top of the slots in the side of the tray. Pins in Slots Step 13. Use six, M5 x 12 screws (without washers) to attach the tray to the slides. Three screws are used to attach each slide. Insert the screws through the slides, through the tray and tighten into the threaded nuts located on the inside of the sides of the tray. 3 Pan Head M5x12 T25 screws on each side Step 14. From the bottom of the tray pull the plunger pin down and give it a 1/4 turn to hold it in place. Chapter 2 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
Chapter 2
Server Unpacking and Installation
Install Stand-Alone Server in a Cabinet
17
Step 12.
Take the tray and place it onto the pins that extend from the slides' inner members. The slots with
wide lead-in guides on the side of the tray fit down onto the slides' pins. The flat part of the tray will
be on top, and the mounting holes in the top of the tray will be located to the right of the center of
the tray. Slide the tray all the way down on both sides so that the pins reach the top of the slots in
the side of the tray.
Step 13.
Use six, M5 x 12 screws (without washers) to attach the tray to the slides. Three screws are used to
attach each slide. Insert the screws through the slides, through the tray and tighten into the
threaded nuts located on the inside of the sides of the tray.
Step 14.
From the bottom of the tray pull the plunger pin down and give it a 1/4 turn to hold it in place.
Pins in Slots
3 Pan Head
M5x12 T25 screws
on each side