HP rp5400 User Guide - HP rp5400 Family of Servers - Page 173

HotSwap Power Supply Replacement, the server. The Power Supply LED should illuminate immediately.

Get HP rp5400 PDF manuals and user guides View all HP rp5400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 173 highlights

Removing and Replacing Components Individual Component Remove/Replace Instructions HotSwap Power Supply Replacement Up to three power supplies (0 through 2), located across the bottom front of the server, can be installed in the server without removing power. To replace a power supply, perform the following steps: CAUTION Be careful when putting the power supply into the server. It is heavier than it appears. 1. Grasp the handle in one hand and support the power supply with the other. Slide the power supply into the server. The Power Supply LED should illuminate immediately. 2. Replace the T-15 mounting screw located to the right of the handle near the top of the power supply. The following graphic shows a front and rear view of a HotSwap Power Supply. Chapter 7 159

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
  • 229
  • 230
  • 231
Chapter 7
Removing and Replacing Components
Individual Component Remove/Replace Instructions
159
HotSwap Power Supply Replacement
Up to three power supplies (0 through 2), located across the bottom front of the server, can be installed in the
server without removing power.
To replace a power supply, perform the following steps:
CAUTION
Be careful when putting the power supply into the server. It is heavier than it appears.
1. Grasp the handle in one hand and support the power supply with the other. Slide the power supply into
the server. The Power Supply LED should illuminate immediately.
2. Replace the T-15 mounting screw located to the right of the handle near the top of the power supply.
The following graphic shows a front and rear view of a HotSwap Power Supply.