Honeywell HRSD40F250 User Guide - Page 57

Selecting the Transfer Quality, Setting Up Connectability Using LAN

Get Honeywell HRSD40F250 PDF manuals and user guides View all Honeywell HRSD40F250 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Configuration 2. Use the Up and Down arrows to select a transfer speed unit of measure, either bps or ips. 3. Press to set the unit of measure. Note The local recording speed might be affected by various network bandwidth (Transfer Speed) conditions. Selecting the Transfer Quality 1. Select the field beside Quality, then press . 2. Use the Up and Down arrows to select a quality, either Very High, High, Standard, or Low. 3. Press to set the quality. Note Higher Quality settings require higher Transfer Speed settings. The transfer speed you set is the maximum speed. Depending on the network environment, this speed may not be achieved. Supporting Two-Way Audio Communications This DVR supports two-way audio communications between a local system and a PC running RAS (Remote Access Software). Select the field next to Remote Audio Channel and press to select the audio channel that sends audio to the remote site. Select Select From RAS to send audio of the channel selected from RAS. Note Depending on network conditions, audio might be interrupted or out of synchronization during transmission. Setting Up Connectability Using LAN In the Network Setup screen, select the LAN tab. The LAN (Manual) Setup screen appears. Document 800-03097 Rev C 57 03/09

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
Document 800-03097
Rev C
57
03/09
Configuration
2.
Use the
Up
and
Down
arrows to select a transfer speed unit of measure, either
bps or ips.
3.
Press
to set the unit of measure.
Note
The local recording speed might be affected by various network
bandwidth (Transfer Speed) conditions.
Selecting the Transfer Quality
1.
Select the field beside
Quality
, then press
.
2.
Use the
Up
and
Down
arrows to select a quality, either Very High, High, Standard,
or Low.
3.
Press
to set the quality.
Note
Higher Quality settings require higher Transfer Speed settings.
The transfer speed you set is the maximum speed. Depending
on the network environment, this speed may not be achieved.
Supporting Two-Way Audio Communications
This DVR supports two-way audio communications between a local system and a PC
running RAS (Remote Access Software).
Select the field next to
Remote Audio Channel
and press
to select the audio
channel that sends audio to the remote site. Select
Select From RAS
to send audio of
the channel selected from RAS.
Note
Depending on network conditions, audio might be interrupted or
out of synchronization during transmission.
Setting Up Connectability Using LAN
In the Network Setup screen, select the
LAN
tab. The LAN (Manual) Setup screen
appears.