Home » Kyocera Manuals » Laser Printers » Kyocera FS 3830N » Manual Viewer

Kyocera FS 3830N FS-3820N/3830N Operation Guide Rev-1.1 - Page 223

USB Universal Serial Bus, Simple Network Management

Add to My Manuals
Save this manual to your list of manuals

Page 223 highlights

Glossary Operator panel This is located on the top of the printer. The panel consists of the message display three indicators and eight keys. The message display shows the printer's status. Press the keys when you want to switch the printer between online and offline status, or to cancel printing. Outline font With outline fonts, characters outlines are represented by numerical expressions, and fonts can be enlarged, reduced, or painted in different ways by changing the numeric values of those expressions. Printing remains clear even if you enlarge fonts, since the letters are defined by an outline. You can specify font size in steps of 0.25 points up to 999.75 points. Parallel interface With this interface, data transfer between the printer and the computer takes place on 8-bit chunks. The printer can perform IEEE1284 compatible bi-directional communications. Printer driver The printer driver makes it possible for you to print data created using application software. The printer driver for either the printer is on the CD-ROM supplied with the printer. Install the printer driver on the computer connected to the printer. Simple Network Management Protocol (SNMP) This is a protocol for the management of networks that use TCP/IP (Transmission Control Protocol/Internet Protocol). Sleep mode This mode is activated after a specified amount of time elapses. The printer goes into economy mode and a minimum amount of power is consumed. You can change the amount of time before the printer goes into sleep mode from the printer's operator panel. The default setting is 15 minutes. Status page This lists printer conditions, such as the printer's memory, the total number of copies printed, and paper source settings. USB (Universal Serial Bus) An interface standard for tow to middle speed serial interfaces. This printer supports Hi-Speed USB 2.0. The maximum transfer rate is 480 Mbps and the maximum cable length is 5 meters (16 feet). RAM disk This is a virtual disk drive that uses part of the printer's memory. With RAM disk you can set any memory size arbitrarily, and use electronic sorting (to reduce print time). Rear tray Tray installed at the rear of the printer. Select paper output to the rear tray when printing on postcards, envelopes, or labels. Glossary-3

Section	Page
Contents	5
Introduction	10
Features	11
For More Information...	14
Guide to the Operation Guide	15
Chapter 1 Using the Operator Panel	17
Understanding the Operator Panel	18
Message Display	18
Interface Indicator	19
Paper Size Indicator	19
Paper Type Indicator	20
READY, DATA, and ATTENTION Indicators	20
Keys	21
Menu System Road Map	22
Printing Test Pages	28
Menu Map	28
Status Page	30
Service Status Page	34
Network Interface Status Page	35
Font Lists	37
Received Data Dumping	39
Paper Handling	40
Setting the Paper Size	40
Setting the Paper Size in Paper Cassette	40
Setting the Paper Size in MP Tray	44
Setting the Paper Type	46
Setting the Paper Type in Paper Cassette	46
Setting the Paper Type in MP Tray	47
Creating Custom Paper Type	48
Resetting the Custom Paper Type	52
MP Tray Mode	53
Selecting the Paper Feed Source	54
Selecting the Output Stack	55
Overriding A4 and Letter Size Difference	56
Pagination	57
Emulation	57
Changing the Emulation	57
Alternative Emulation for KPDL Emulation	58
Printing KPDL Errors	59
Font	60
Default font	60
Default Font Size	62
Changing Type for Courier/Letter Gothic	63
Setting the Character Pitch for Courier/Letter Gothic	64
Code Set	65
Number of Copies	66
Printing Orientation	67
KIR (Kyocera Image Refinement)	68
Ecoprint	70
Resolution	71
e-MPS	72
Quick Copy	73
Proof and Hold	75
Printing a Private Job	77
Printing a Stored Job	79
Printing a Code Job	81
Printing a List of Code Jobs	83
Retrieving Jobs from Virtual Mailbox (VMB)	84
Printing a List of VMB	85
e-MPS Configuration	86
Interface	90
Parallel Interface Mode	90
USB Interface Mode	91
Serial Interface Parameters	92
Network Interface Parameters	94
Operating the Storage Device	97
Activating the RAM Disk	97
Reading Data	99
Writing Data	100
Deleting Data	102
Reading Fonts from a CompactFlash Card	103
Formatting a Storage Device	104
Printing a List of Data Names	105
Configuration	107
Page Protect Mode	107
Linefeed (LF) Action	108
Carriage-Return (CR) Action	109
Wide A4 Pitch	110
Print Density	111
Total Printed Pages	112
Toner Counter Resetting	112
Message Language	113
Automatic Form Feed Timeout	115
Sleep Timer Setting	116
Printer Resetting	118
Resource Protection	119
Alarm (Buzzer) Setting	120
Auto Continue Setting	121
Duplex Printing Error Detection Setting	123
Chapter 2 Paper Selection	124
General Guidelines	125
Paper Availability	125
Paper Specifications	125
Selecting the Right Paper	126
Special Paper	130
Transparency (Overhead Projection Film)	130
Adhesive-Backed Labels	131
Paper Type	135
Chapter 3 Maintenance	136
Toner Container Replacement	137
Toner Container Replacement Interval	137
Replenishing Toner	138
Waste Toner Box Replacement	141
Replacing the Waste Toner Box	141
Cleaning	144
Cleaning the Charger Wire	144
Cleaning the Charger Grid	145
Paper Transfer Unit	148
Chapter 4 Troubleshooting	149
General Guide	150
Print Quality Problems	151
Indicators and Messages	154
Indicators	154
Maintenance Messages	155
Error Messages	158
Correcting a Paper Jam	160
Jam at the Paper Cassette or Inside the Printer	162
Paper Jam at the Option Duplexer	164
Paper Jam at the Option Sorter	166
Jam at the MP Tray	168
Chapter 5 Fonts	169
List of Fonts	170
PCL (Scalable and Bitmap) Fonts	170
KPDL Fonts (1)	173
KPDL Fonts (2)	174
Appendix A Options	175
Available Options	176
Expanding the Printer Memory	177
Installing Option Units	183
PF-60 Paper Feeder	183
DU-61 Duplexer	186
SO-60 Sorter	189
EF-60 Envelope Feeder	195
PT-4/PT-60 Rear Tray	199
Network Interface Card	200
Microdrive (Hard Disk)	202
CompactFlash (Memory) Card	204
Appendix B Host Computer Interface	205
Parallel Interface	206
Parallel Interface Communication Modes	206
Interface Signals	206
USB Interface	209
Specifications	209
Interface Signals	209
Serial Interface (Option)	210
RS-232C Interface	210
RS-232C Protocol	211
PRESCRIBE FRPO D0 Command	213
RS-232C Cable Connection	214
Obtain a Suitable RS-232C Cable	214
Connecting the Printer to the Computer	214
Appendix C Specifications	218
Glossary	221

Match case Limit results 1 per page

Glossary

Glossary-3

Operator panel

This is located on the top of the printer. The

panel consists of the message display three

indicators and eight keys. The message display

shows the printer’s status. Press the keys when

you want to switch the printer between online

and offline status, or to cancel printing.

Outline font

With outline fonts, characters outlines are

represented by numerical expressions, and fonts

can be enlarged, reduced, or painted in different

ways by changing the numeric values of those

expressions. Printing remains clear even if you

enlarge fonts, since the letters are defined by an

outline. You can specify font size in steps of 0.25

points up to 999.75 points.

Parallel interface

With this interface, data transfer between the

printer and the computer takes place on 8-bit

chunks. The printer can perform IEEE1284

compatible bi-directional communications.

Printer driver

The printer driver makes it possible for you to

print data created using application software.

The printer driver for either the printer is on the

CD-ROM supplied with the printer. Install the

printer driver on the computer connected to the

printer.

RAM disk

This is a virtual disk drive that uses part of the

printer’s memory. With RAM disk you can set

any memory size arbitrarily, and use electronic

sorting (to reduce print time).

Rear tray

Tray installed at the rear of the printer. Select

paper output to the rear tray when printing on

postcards, envelopes, or labels.

Simple Network Management

Protocol (SNMP)

This is a protocol for the management of

networks that use TCP/IP (Transmission Control

Protocol/Internet Protocol).

Sleep mode

This mode is activated after a specified amount

of time elapses. The printer goes into economy

mode and a minimum amount of power is

consumed. You can change the amount of time

before the printer goes into sleep mode from the

printer’s operator panel. The default setting is 15

minutes.

Status page

This lists printer conditions, such as the printer’s

memory, the total number of copies printed, and

paper source settings.

USB (Universal Serial Bus)

An interface standard for tow to middle speed

serial interfaces. This printer supports Hi-Speed

USB 2.0. The maximum transfer rate is

480 Mbps and the maximum cable length is

5 meters (16 feet).