Lexmark Optra C Service Manual - Page 184
Transfer Drum Sensors, See Assembly 29-3.
 |
View all Lexmark Optra C manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 184 highlights
5045-001 Transfer Drum Sensors See Assembly 29-3. Note: This sensor is used in two places on the transfer drum assembly. One of the sensors is on the inside of the drum and one on the outside of the drum. To remove the sensor on the inside of the drum, follow the removal procedure to remove the transfer drum solenoid (Asm 29-5) and remove the sensor. To remove the sensor from the outside of the drum, use the procedures that follow: 1. Remove the transfer drum and holder assembly. 2. The sensor is located in the middle of the separation claw. Remove the cover from the sensor. 3. Disconnect the connector from the sensor. 4. Pry the four sensor latches from the cover and remove the sensor. 4-58
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179 -
180 -
181 -
182 -
183 -
184 -
185 -
186 -
187 -
188 -
189 -
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
 |
 |
4-58
5045-001
Transfer Drum Sensors
See Assembly 29-3.
Note:
This sensor is used in two places on the transfer drum
assembly. One of the sensors is on the inside of the drum and one
on the outside of the drum. To remove the sensor on the inside of the
drum, follow the removal procedure to remove the transfer drum
solenoid (Asm 29-5) and remove the sensor. To remove the sensor
from the outside of the drum, use the procedures that follow:
1. Remove the transfer drum and holder assembly.
2. The sensor is located in the middle of the separation claw.
Remove the cover from the sensor.
3. Disconnect the connector from the sensor.
4. Pry the four sensor latches from the cover and remove the
sensor.