Nokia IP1220 Installation Guide - Page 108

Installing or Replacing a Power Supply

Get Nokia IP1220 - Security Appliance PDF manuals and user guides View all Nokia IP1220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 108 highlights

7 Installing and Replacing Components Other than Network Interface Cards (NICs) and Accelerated Data Path 3. Slowly pull the fan unit out of the chassis toward the rear. 00318.1 4. If the IP1200 Series appliance is running, immediately install a replacement fan unit by sliding it into the back of the appliance. 5. Tighten the four retaining screws on the new fan unit. Installing or Replacing a Power Supply The power supplies in the Nokia IP1200 Series appliance are hot swappable, and perform load sharing while two active power supplies are connected in parallel. Load sharing increases the life of the power supplies. Note On an appliance with two active power supplies installed, both power supplies should be turned on for load sharing and redundancy. If both power supplies are not turned on, the Fault LED illuminates. For more information about the Fault LED, see "Power Supply Status LEDs" on page 28. The power supplies are autosensing and can accept input voltages between 85 VAC and 264 VAC. The power supply output is regulated to a tolerance of ± 5 percent of the specified output voltage. Under certain circumstances, the power supplies feel hot to the touch. This happens when the power supply is connected to AC power, but is not turned on. In this state the 3.3 V standby circuitry is powered on, causing the power supply to heat up. Because the power supply is not turned on, the integrated cooling fan is not operating. In this situation, the power supply still meets all safety standards.This condition is normal and does not affect the performance of the Nokia IP1200 Series. To cool the power supply down, use the power supply switch to turn on power and activate the integrated cooling fan. 108 IP1220 and IP1260 Security Platforms Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
7
Installing and Replacing Components Other than Network Interface Cards (NICs) and Accelerated Data Path
108
IP1220 and IP1260 Security Platforms Installation Guide
3.
Slowly pull the fan unit out of the chassis toward the rear.
4.
If the IP1200 Series appliance is running, immediately install a replacement fan unit by
sliding it into the back of the appliance.
5.
Tighten the four retaining screws on the new fan unit.
Installing or Replacing a Power Supply
The power supplies in the Nokia IP1200 Series appliance are hot swappable, and perform load
sharing while two active power supplies are connected in parallel. Load sharing increases the life
of the power supplies.
Note
On an appliance with two active power supplies installed, both power supplies should be
turned on for load sharing and redundancy. If both power supplies are not turned on, the
Fault LED illuminates. For more information about the Fault LED, see
“Power Supply Status
LEDs”
on page 28.
The power supplies are autosensing and can accept input voltages between 85 VAC and 264
VAC. The power supply output is regulated to a tolerance of ± 5 percent of the specified output
voltage.
Under certain circumstances, the power supplies feel hot to the touch. This happens when the
power supply is connected to AC power, but is not turned on. In this state the 3.3 V standby
circuitry is powered on, causing the power supply to heat up. Because the power supply is not
turned on, the integrated cooling fan is not operating.
In this situation, the power supply still meets all safety standards.This condition is normal and
does not affect the performance of the Nokia IP1200 Series. To cool the power supply down, use
the power supply switch to turn on power and activate the integrated cooling fan.
00318.1