Nokia IP1220 Installation Guide - Page 72

Nokia ADP Card Interface Names for IP1220 and IP1260 Appliances, ADP module with PMC NICs.

Get Nokia IP1220 - Security Appliance PDF manuals and user guides View all Nokia IP1220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 72 highlights

6 About IP1200 Appliance ADP Services Modules These changes can affect any features or protocols that use the existing interfaces or their addresses, including the following: „ Dynamic routing protocols „ Multicast routing protocols „ Static routing configuration „ VRRP „ IP clustering „ Transparent mode „ Link aggregation „ Link redundancy „ Traffic management/QoS Note After you install an ADP module, reconfigure any protocols and features that used the removed interfaces to use the ADP interfaces. Reassign IP addresses from the removed interfaces to the ADP interfaces as appropriate. Nokia ADP Card Interface Names for IP1220 and IP1260 Appliances ADP module interface naming conventions differ from those for PMC NICs IP1220 and IP1260 appliances support one ADP module, which you install in slots 1 and 2. The eight ports on your ADP module are named as follows: eth-s2p1, eth-s2p2, eth-s2p3, eth-s2p4, eth-s2p5, eth-s2p6, eth-s2p7, eth-s2p8 Since the ADP interface names are not exactly the same as other PMC NIC interface names, you need to reconfigure your appliance when you replace PMC NICs with an ADP module or an ADP module with PMC NICs. 72 IP1220 and IP1260 Security Platforms Installation Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
6
About IP1200 Appliance ADP Services Modules
72
IP1220 and IP1260 Security Platforms Installation Guide
These changes can affect any features or protocols that use the existing interfaces or their
addresses, including the following:
Dynamic routing protocols
Multicast routing protocols
Static routing configuration
VRRP
IP clustering
Transparent mode
Link aggregation
Link redundancy
Traffic management/QoS
Note
After you install an ADP module, reconfigure any protocols and features that used the
removed interfaces to use the ADP interfaces. Reassign IP addresses from the removed
interfaces to the ADP interfaces as appropriate.
Nokia ADP Card Interface Names for IP1220 and IP1260
Appliances
ADP module interface naming conventions differ from those for PMC NICs
IP1220 and IP1260 appliances support one ADP module, which you install in slots 1 and 2. The
eight ports on your ADP module are named as follows:
eth-s2p1, eth-s2p2, eth-s2p3, eth-s2p4, eth-s2p5, eth-s2p6, eth-s2p7, eth-s2p8
Since the ADP interface names are not exactly the same as other PMC NIC interface names, you
need to reconfigure your appliance when you replace PMC NICs with an ADP module or an
ADP module with PMC NICs.