Nokia IP1220 Installation Guide - Page 69

To install or remove ADP transceivers in a Nokia ADP module

Get Nokia IP1220 - Security Appliance PDF manuals and user guides View all Nokia IP1220 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Installing and Replacing ADP Modules „ After you slide the ADP module into both carrier slots, first secure the two bottom screws, and then secure the two top screws. Ensure that both of the ejector and locking levers are fully secured. „ After you physically install the ADP module, reboot the system and reconfigure the interfaces as described in "Configuring Nokia IPSO for IP1220 and IP1260 ADP Interfaces" on page 71. The following figure shows an IP1220 and IP1260 ADP module and card carrier assembly. Link and Activity LEDs Power LED illuminates green when the module is under power ADP Card 1 2 3 4 5 6 POWER 7 8 1000BaseX 1000BaseX 00651 Ejector and locking levers To install or remove ADP transceivers in a Nokia ADP module Refer to the following figure, which shows how to install or remove Nokia ADP module transceivers. The transceivers are hot swappable as are the interface cables you use with them. Rotate the latch levers up or down to secure transceivers, or to release them for removal. You do not need to change the interface type in Network Voyager or the CLI, as the system makes the configuration changes automatically. To identify whether a fiber transceiver you are using is short-range or long-range, refer to the color of the latch lever as follows: IP1220 and IP1260 Security Platforms Installation Guide 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
Installing and Replacing ADP Modules
IP1220 and IP1260 Security Platforms Installation Guide
69
After you slide the ADP module into both carrier slots, first secure the two bottom screws,
and then secure the two top screws. Ensure that both of the ejector and locking levers are
fully secured.
After you physically install the ADP module, reboot the system and reconfigure the
interfaces as described in
“Configuring Nokia IPSO for IP1220 and IP1260 ADP Interfaces”
on page 71.
The following figure shows an IP1220 and IP1260 ADP module and card carrier assembly.
To install or remove ADP transceivers in a Nokia ADP module
Refer to the following figure, which shows how to install or remove Nokia ADP module
transceivers. The transceivers are hot swappable as are the interface cables you use with them.
Rotate the latch levers up or down to secure transceivers, or to release them for removal. You do
not need to change the interface type in Network Voyager or the CLI, as the system makes the
configuration changes automatically.
To identify whether a fiber transceiver you are using is short-range or long-range, refer to the
color of the latch lever as follows:
00651
1000BaseX
1
2
3
4
1000BaseX
5
6
7
8
ADP Card
POWER
Power LED illuminates green when
the module is under power
Ejector and locking levers
Link and Activity LEDs