Home » Nokia Manuals » Network Security & Firewall Devices » Nokia IP1220 » Manual Viewer

Nokia IP1220 Installation Guide - Page 73

Configuration Example with VRRP

Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Configuring Nokia IPSO for IP1220 and IP1260 ADP Interfaces Configuration Example with VRRP This example describes the steps required to install an ADP module in an IP1220 or IP1260 appliance with VRRP configured. The following figure shows the Interface Configuration page of the platform before an ADP module is installed. Interfaces are installed in slots 1, 2, and 3. For this example, legacy monitored-circuit VRRP is enabled and configured with these settings: „ Interface eth-s1/s1p1c0 is assigned the IP address 10.1.1.1 (not shown) and uses 10.1.1.99 as the VRRP backup address. „ Interface eth-s1/s1p2c0 backs up interface eth-s1/s1p1c0. IP1220 and IP1260 Security Platforms Installation Guide 73

Section	Page
Title Page	1
Contact Information	3
Contents	5
Figures	9
Tables	11
About this Guide	13
In this Guide	13
Conventions this Guide Uses	14
Notices	14
Text Conventions	14
Related Documentation	15
1 Overview	17
About the Nokia IP1200 Series Security Platform	17
About the Nokia IP1200 Series Flash-Based Security Platforms	18
Managing the Nokia IP1200 Series Security Platform	19
Nokia IP1200 Series Security Platform Overview	19
Ethernet Management Ports	20
PMC Expansion Slots	21
Console Port	21
System Status LEDs	23
Hard-Disk Drives	24
Power Supplies and Fan Unit	25
Site Requirements	28
Safety Warnings and Cautions	28
Software Requirements	30
Product Disposal	30
2 Installing the Nokia IP1200 Series Appliance	33
Rack Mounting the Appliance	33
Before You Begin	34
3 Performing the Initial Configuration	39
Using a Console Connection	40
Connecting Power and Turning the Power On	40
Performing the Initial Configuration	42
Connecting Network Interfaces	44
Using Nokia Network Voyager	44
Viewing Nokia IPSO Documentation by Using Nokia Network Voyager	45
Using the Command-Line Interface	46
Using Nokia Horizon Manager	46
4 Installing and Replacing Network Interface Cards and Accelerated Data Path (ADP) Services Modules	49
Removing, Installing, and Replacing NICs or the ADP Module	50
Before You Begin	50
Configuring and Activating Interfaces	56
Monitoring Network Interface Cards	56
5 About IP1200 Series Appliance Network Interface Cards	57
Four-Port 10/100 Ethernet NICs	58
10/100 Ethernet NIC Features	58
Ethernet NIC Connectors and Cables	59
Two-Port and Four-Port Copper Gigabit Ethernet NICs	60
Copper Gigabit Ethernet NIC Features	61
Performance Considerations	62
Copper Gigabit Ethernet NIC Connectors and Cables	62
Two-Port Fiber-Optic Gigabit Ethernet NICs	64
Fiber-Optic Gigabit Ethernet NIC Features	64
Fiber-Optic Gigabit Ethernet NIC Connectors and Cables	65
Performance Considerations	65
6 About IP1200 Appliance ADP Services Modules	67
Installing and Replacing ADP Modules	68
Nokia ADP Card LED Reference Information	71
Configuring Nokia IPSO for IP1220 and IP1260 ADP Interfaces	71
Effect on Interfaces	71
Nokia ADP Card Interface Names for IP1220 and IP1260 Appliances	72
Configuration Example with VRRP	73
7 Installing and Replacing Components Other than Network Interface Cards (NICs) and Accelerated D...	81
Replacing a Hard-Disk Drive	82
Disk Mirroring	82
Hard-Disk Drive Hot Swap Feature	83
Before You Begin	83
Installing a PC Card	88
Storing System Logs on the Flash-Memory PC Card	94
Disabling Flash-Memory PC Cards	94
Transferring Files with the Flash-Memory PC Card	95
Replacing the Compact Flash Memory Card	96
Replacing or Upgrading Memory	99
Before You Begin	99
Installing a Nokia Encryption Accelerator Card	102
Before You Begin	103
Configuring Software to Use Hardware Acceleration	106
Installing a Fan Unit	107
Before You Begin	107
Installing or Replacing a Power Supply	108
Before You Begin	109
Monitoring the Power Supply	110
Replacing Motherboard Batteries	110
Before You Begin	111
8 Troubleshooting	113
General Troubleshooting Information	113
A Technical Specifications	119
Space Requirements	119
B Compliance Information	121
Declaration of Conformity	121
Compliance Statements	122
FCC Notice (US)	123
Index	125
Numerics	125
A	125
C	125
D	125
E	125
F	125
G	125
H	126
I	126
L	126
M	126
N	126
O	126
P	126
R	126
S	126
T	126
U	127
V	127

Match case Limit results 1 per page

Configuring Nokia IPSO for IP1220 and IP1260 ADP Interfaces

IP1220 and IP1260 Security Platforms Installation Guide

Configuration Example with VRRP

This example describes the steps required to install an ADP module in an IP1220 or IP1260

appliance with VRRP configured. The following figure shows the Interface Configuration page

of the platform before an ADP module is installed. Interfaces are installed in slots 1, 2, and 3.

For this example, legacy monitored-circuit VRRP is enabled and configured with these settings:

Interface eth-s1/s1p1c0 is assigned the IP address 10.1.1.1 (not shown) and uses 10.1.1.99 as

the VRRP backup address.

Interface eth-s1/s1p2c0 backs up interface eth-s1/s1p1c0.