Polaroid LDTV152 Owners Guide - Page 70

Appendix C, Programming the Remote Control, continued

Page 70 highlights

70 Appendices Appendix C: Programming the Remote Control, continued Programming the Remote Control 1. Move the slide switch at the top of the remote to the position for the product you want to control. Refer to the table below. Only one of each device type can be controlled in each slide-switch position. Switch Position CABLE/SAT Affected Device Cable Box DTV Receiver Satellite Receiver VCR VCR DVR Laser Disc Player DVD Player/Recorder DVD DVD Player/Recorder DVR Laser Disc Player VCR AUDIO A/V Receiver Audio Amplifier CD Player 2. Press and hold POWER on the remote control for several seconds until the button blinks twice and goes off. 3. Release the POWER button. 4. Enter the first five-digit code listed for your equip- ment. • The POWER button blinks twice when you start to enter the code and then once for each additional keypress. • The POWER button blinks twice when you finish entering a valid code. • Move the slide switch to another position if you need to start over or wish to exit programming mode. 5. Point the remote control at the equipment and press POWER. If the product has no power on/off function, press a different key, such as (PLAY), (STOP), VOL , or MUTE. • If the equipment responds, the remote control is properly programmed to operate the equipment. • If the equipment does not respond, repeat steps 2-4 with the next five-digit code listed for your equipment. IMPORTANT You may need to reprogram the remote control after changing the batteries. 6. Once you have found the correct code, write it in the space below for future reference. Switch Position CABLE/SAT VCR DVD AUDIO Device Type Code Code Verification To determine the code programmed for any position of the slide switch: 1. Move the slide switch to the position you wish to verify. 2. Press and hold POWER on the remote control for several seconds until the button blinks twice and goes off. 3. Press keys 9 9 0 4. Press 1 and count the blinks of the power button. Write down the number of blinks as the first digit of the code. 5. Repeat step 4 for the second, third, fourth, and fifth digits of the code. Audio Lock: Universal A/V Receiver Control With Audio Lock active, the remote control operates the volume and mute functions of the A/V receiver in all positions of the slide switch. Activate Audio Lock if you normally use an A/V receiver with your TV and other A/V equipment. 1. Program the AUDIO position for your A/V receiver as described earlier in this section. 2. With the slide switch in the AUDIO position, press and hold POWER on the remote control for several seconds until the button blinks twice and goes off. 3. Press keys 9 9 3 ENTER The POWER button will blink twice to indicate Audio Lock is active. To Reset the Remote Control to Operate Volume and Mute for the TV Speakers 1. Press and hold POWER for several seconds until the key blinks twice and goes off. 2. Press keys 9 9 3 VOL . The POWER key will blink four times to indicate Audio Lock has cleared.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96

70
Appendices
IMPORTANT
You may need to reprogram the remote
control after changing the batteries.
Programming the Remote Control
Move the slide switch at the top of the remote to
1.
the position for the product you want to control.
Refer to the table below.
Only one of each device
type can be controlled in each slide-switch position.
Switch Position
Affected Device
CABLE/SAT
Cable Box
DTV Receiver
Satellite Receiver
VCR
VCR
DVR
Laser Disc Player
DVD Player/Recorder
DVD
DVD Player/Recorder
DVR
Laser Disc Player
VCR
AUDIO
A/V Receiver
Audio Amplifier
CD Player
Press and hold
2.
POWER
on the remote control for
several seconds until the button blinks twice and
goes off.
Release the
3.
POWER
button.
Enter the first five-digit code listed for your equip-
4.
ment.
The
POWER
button blinks twice when you start to
enter the code and then once for each addi-
tional keypress.
The
POWER
button blinks twice when you finish
entering a valid code.
Move the slide switch to another position if you
need to start over or wish to exit programming
mode.
Point the remote control at the equipment and
5.
press
POWER
.
If the product has no power on/off
function, press a different key, such as
(
PLAY
),
(
STOP
),
VOL
, or
MUTE.
If the equipment responds, the remote control
is properly programmed to operate the equip-
ment.
If the equipment does not respond, repeat
steps 2–4 with the next five-digit code listed for
your equipment.
Once you have found the correct code, write it in
6.
the space below for future reference.
Switch Position
Device Type
Code
CABLE/SAT
VCR
DVD
AUDIO
Code Verification
To determine the code programmed for any position of
the slide switch:
Move the slide switch to the position you wish to
1.
verify.
Press and hold
2.
POWER
on the remote control for
several seconds until the button blinks twice and
goes off.
Press keys
3.
9
9
0
Press
4.
1
and count the blinks of the power button.
Write down the number of blinks as the first digit of
the code.
Repeat step 4 for the second, third, fourth, and fifth
5.
digits of the code.
Audio Lock:
Universal
A/V Receiver Control
With Audio Lock active, the remote control operates
the volume and mute functions of the A/V receiver in all
positions of the slide switch.
Activate Audio Lock if you
normally use an A/V receiver with your TV and other
A/V equipment.
Program the
1.
AUDIO
position for your A/V receiver as
described earlier in this section.
With the slide switch in the
2.
AUDIO
position, press
and hold
POWER
on the remote control for several
seconds until the button blinks twice and goes off.
Press keys
3.
9
9
3
ENTER
The
POWER
button will blink twice to indicate Audio
Lock is active.
To
Reset the Remote Control to Operate Volume
and Mute for the TV Speakers
Press and hold
1.
POWER
for several seconds until the
key blinks twice and goes off.
Press keys
2.
9
9
3
VOL
.
The
POWER
key will blink four times to indicate Audio
Lock has cleared.
Appendix C:
Programming the Remote Control, continued