Sony BVME251 Operation Guide - Page 32

[Manual Adjust] Adjusts values by turning the PHASE, CHROMA, BRIGHT, and/or CONTRAST knobs. After adjustment, press the ENTER (Ent) button to confirm the adjusted values.  [Phase]: -150 to +150 (Default value: [000])  [Chroma]: 0000 to 2000 (Default value: [1000])  [Bright]: -500 to +500 (Default value: [000])  [Contrast]: 0000 to 2500 (Default value: [1000] (for [Preset1] to [Preset5]), Default value: [0480] (for [Preset(DCI)])) To display no characters on the screen while adjusting manually Set the CHAR OFF button to on. The characters disappear. To display characters, set the CHAR OFF button to off. To reset the setting to the default Press the corresponding MANUAL button. The adjusted value is reset to the default. To cancel adjustment Press the MENU button. The adjustment data is cleared. To confirm adjustment Press the ENTER (Ent) button. Note During adjustment, the screen saver is activated automatically if the operating conditions are met regardless of the setting of the screen saver function. [Copy From] Copies picture adjustment preset data. Notes  Automatic adjustment data is not copied.  Use the BKM-16R with software version 1.6 or higher or BKM-17R to use the [Copy From] function. Submenu [Preset Value] [Other Monitor] Setting Copies other data in this monitor. When the item is selected, you can select from [Preset1], [Preset2], [Preset3], [Preset4], [Preset5], or [Preset(DCI)]. Copies data from another monitor. [Monitor ID] Note Use the BVM-E251/BVM-E171 as a source monitor to use the [Other Monitor] function. Enter the ID number of the source monitor. When the NETWORK switch is set to PEER TO PEER, this is not selectable. When the ID number is entered, you can select from [Preset1], [Preset2], [Preset3], [Preset4], [Preset5], or [Preset(DCI)]. Submenu [External Memory] Setting Copies data in the USB memory stick, etc. Note Use the USB memory stick, etc. with data stored by the BVM-E251/BVME171 to use the [External Memory] function. When the item is selected, the file names in the source USB memory stick, etc. are displayed. When the file is selected, you can select from [Preset1], [Preset2], [Preset3], [Preset4], [Preset5], or [Preset(DCI)]. [Color Temp Adj] Adjusts the color temperature. When the item is selected, the color temperature data to be adjusted is displayed.  Except for the XYZ format signal When [D93], [D65], [D61], [D55], or [DCI] data is changed, they are displayed as [D93*], [D65*], [D61*], [D55*], or [DCI*]. To change the color temperature data to be adjusted, select [D93], [D65], [D61], [D55], [DCI], [User1], [User2], [User3], [User4], or [User5] in the [Color Temp] menu of the [Channel Configuration] menu.  For the XYZ format signal When [DCI XYZ] data is changed, it is displayed as [DCI XYZ*]. To change the color temperature data to be adjusted, select [DCI XYZ], [User XYZ1], [User XYZ2], [User XYZ3], [User XYZ4], or [User XYZ5] in the [Color Temp] menu (page 36) of the [Channel Configuration] menu. Note If you measure the color temperatures of different display types, such as CRT, LCD, or OLED, by using a common (or general) color analyzer that is based on CIE 1931, and adjust the xy chromaticity to the same value, the appearance may be different because of optical spectrum differences. To compensate for this difference, the [D93], [D65], [D61], [D55], and [User1] to [User5] settings (except DCI) of the monitor are adjusted by an offset 1). 1) The offset value applied (x-0.006, y-0.011) is based on the Judd's function to the CIE 1931 (x, y) value. [Manual] Adjusts the color temperature manually. When the item is selected, the color temperature data to be set is displayed. Except for the XYZ format signal 32 Adjustment Using the Menus