Sony BVME251 Operation Guide - Page 62
Power], On Screen Set], Input Information]
View all Sony BVME251 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 62 highlights
Submenu [1 Pin] - [8 Pin] Setting Assigns the function to each pin of the PARALLEL REMOTE connector when [Parallel Remote] is set to [On]. The default assignment of functions is as follows: 1 Pin: [CH01] 2 Pin: [CH02] 3 Pin: [Marker] 4 Pin: [Mono] 6 Pin: unused 7 Pin: unused 8 Pin: [Tally] You can change the assignment to the following functions for pins 1 to 4 and 6 to 8. The functions shown with item name only are the same as those assigned to the function buttons on the controller. For details on these functions, see [Function Key] (page 71) of the [Controller] menu. [Parallel Remote] (1/4) [CH01] to [CH30]: Selects a channel number. Enter the desired channel number with the numeric buttons Unused [Under Scan] 1), [Over Scan] 1), [Native Scan], [16:9], [H Delay], [V Delay], [Flicker Free] 1) The scan mode is set to [Normal Scan] when [Under Scan] or [Over Scan] is off. [Parallel Remote] (2/4) [Aperture], [Mono], [Blue Only], [R Off], [G Off], [B Off], [Chroma Up], [Interlace] [Tally]: The function to turn on the tally lamp [Sleep]: The monitor power function [Parallel Remote] (3/4) [Marker], [Aspect Marker], [Area Marker 1], [Area Marker 2], [Center Marker], [Aspect MarkerLine], [Aspect Blanking-Half], [Aspect Blanking-Black] [Parallel Remote] (4/4) [Side by Side], [Wipe], [Butterfly], [Blending], [Error Notify Clear], [Audio Level Meter], [ALM Hold Reset], [Time Code] For the pin assignment, see "PARALLEL REMOTE connector" in "Location and Function of Parts and Controls" on page 14. [Power] Sets the status of the monitor when the main power is turned on or the power is turned on by remote operation. Submenu [Sleep Mode] [Power On Status] [Default CH] Setting Sets the status when the main power switch is turned on. [Off]: Operation mode [On]: Sleep mode Sets the input channel when the power is turned on. [Last]: Sets to the channel that was selected at the time the power was last turned off. [CH]: Sets to the channel number specified in Default CH. Selects the channel (01 to 30) when the [Power On Status] is set to [CH]. (Default value: [01]) [On Screen Set] Sets the items for the screen display. [Input Information] Sets the display of the input information. Submenu [Format] Setting Sets the display mode of the signal system. [Auto]: Disappears after being displayed for a while. [Off]: Not displayed. [Position] [CH No] Note The picture rate display is [23.98], [29.97], or [59.94] (example 1080/ 59.94P) when the signal is input from the SDI input, [Format] is set to [3G/ HD/SD-SDI Auto] (page 38) in the [Channel Configuration] menu, and the Picture Rate information for the Payload ID is 23.98, 29.97, or 59.94, even if the monitor determines the picture rate as 24Hz, 30Hz, or 60Hz. For details on Payload ID, see [SDI Payload ID Status] (page 69) of the [System Status] menu or "Displaying the Monitor Status Page" (page 74). Sets the display position for the signal system. [Top Left]: top left [Top Center]: top center [Top Right]: top right [Bottom Left]: bottom left [Bottom Center]: bottom center [Bottom Right]: bottom right Sets the display mode of the channel number. [Auto]: Disappears after being displayed for a while. [Off]: Not displayed. 62 Adjustment Using the Menus