Sony BVME251 Operation Guide - Page 65
Password], Date/Time], To cancel the time code display, Over Range], ABL Notification]
View all Sony BVME251 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 65 highlights
1 Input the SDI signal. 2 Select the channel. 3 Set the time code in the [Time Code] menu (page 64) of the [On Screen Set] menu in the [System Configuration] menu. 4 Set [Time Code] (page 59) to [On] in the [Function Switch] menu of the [Function Setting] menu or by pressing the TIME CODE button of the controller. The time code is displayed. To cancel the time code display Set [Time Code] (page 59) to [Off] in the [Function Switch] menu of the [Function Setting] menu or by pressing the TIME CODE button of the controller. Note Use the BKM-16R with software version 1.4 or higher or BKM-17R to assign [Time Code] or [ALM Hold Reset] function to a function button of the controller. [Over Range] When a portion of the signal exceeds the dynamic range of the internal signal processing circuit, it is determined as over range. This menu sets whether or not to display a zebra pattern on the detected over range portion ([Off], [On]). When over range is detected, adjust the contrast or brightness to a lower level. Notes When over range occurs, the OVER RANGE indicator on the front of the unit does not light in amber in the following circumstances regardless of the setting of this menu. - when the monitor is in the HDR display - when [S-LOG2(SDR)] or [S-LOG3(SDR)] is selected When [Gamut Error Display] of the [Function Setting] menu is set to [On], the zebra pattern in the area where the error was detected is also included as a detection target of over range. [ABL Notification] Sets whether or not to display [ABL] on the screen when ABL starts ([Off] or [On]). Note When the gamut error notification is displayed on the screen, [ABL] is not displayed, even though [ABL Notification] is set to [On] and ABL is activated. [Password] Sets the password for the menu. Enter a four-digit number for the password. (Default value: [9999]) [Change Password] Changes the password. [Enter New Password]: Enter a new password with the numeric buttons and press the ENTER (Ent) button. [Re-Enter Password]: Enter the new password again and press the ENTER (Ent) button. The password is registered. To change it, press the MENU button. [Apply Password] Sets whether or not to apply the password to each menu ([Yes] or [No]). Submenu Setting [Adjustment] [Yes]: Apply the password. [No]: Do not apply the password. [Channel Configuration] [Yes]: Apply the password. [No]: Do not apply the password. [Auxiliary Setting] [Yes]: Apply the password. [No]: Do not apply the password. [Function Setting] [Yes]: Apply the password. [No]: Do not apply the password. [System Configuration] [Yes]: Apply the password. [No]: Do not apply the password. [Individual Item] Sets whether or not to apply the password to the [System Configuration] menu. [Network] [Yes]: Apply the password. [No]: Do not apply the password. [Parallel Remote] [Yes]: Apply the password. [No]: Do not apply the password. [Power] [Yes]: Apply the password. [No]: Do not apply the password. [On Screen Set] [Yes]: Apply the password. [No]: Do not apply the password. [Date/Time] [Yes]: Apply the password. [No]: Do not apply the password. [Scan Mode Skip] [Yes]: Apply the password. [No]: Do not apply the password. [Screen Saver] [Yes]: Apply the password. [No]: Do not apply the password. [File Management] [Yes]: Apply the password. [No]: Do not apply the password. [Controller] [Yes]: Apply the password. [No]: Do not apply the password. [Key Protect] [Yes]: Apply the password. [No]: Do not apply the password. [Date/Time] When the item is selected, you can set or change the date and time. 65 Adjustment Using the Menus