Sony BVME251 Operation Guide - Page 71

Submenu [SDCP/SDAP Community] [SDCP Port No] [SDAP Port No] [SDAP Broadcast] [SDAP Broadcast Period] [Reset Protocol Setting] Setting Sets the SDCP/SDAP community name. When the item is selected, you can enter the community name (four characters).  [SONY]: SONY is entered as a community name.  [New Name]: Enter a new name. Sets the SDCP port number. Set from 53434 to 53534. (Default value: [53484]) Sets the SDAP port number. Set from 53812 to 53912. (Default value: [53862]) Sets whether or not to issue the SDAP ([Disable] or [Enable]). Sets the period (seconds) to issue the SDAP. Set from 05 to 30. (Default value: [30]) Resets the protocol setting. When the item is selected, the following message appears. [Are you sure ?]  [OK]: To reset data, press the ENTER (Ent) button.  [Cancel]: To cancel, press the MENU button. [Function Key] Assigns the function to the function buttons of the controller. For details on the function assignment, see "Assigning a Function to a Function Button" (page 72). Notes  Use the BKM-16R with software version 1.6 or higher or BKM-17R to assign [Status], [Center Marker], [Aspect Marker-Line], [Aspect Blanking-Half], [Aspect Blanking-Black], [Difference], [Horopter Check], [Flip H].  Use the BKM-16R with software version 1.5 or higher or BKM-17R to assign [Checkerboard] and [L/R Switch].  Use the BKM-16R with software version 1.4 or higher or BKM-17R to assign [Audio Level Meter], [ALM Hold Reset] and [Time Code].  Use the BKM-16R with software version 1.3 or higher or BKM-17R to assign [Black Detail Mode].  Use the BKM-17R to assign [Flicker Free]. Submenu [F1]-[F16] Setting The following functions are assigned.  [Scan Mode]: Changes the scan mode of the picture.  [Native Scan]: Displays the picture in native scan mode. Submenu Setting  [16:9]: Changes the aspect ratio to 16:9 or 1.896:1 (digital cinema signal), and when set to Off, the aspect ratio changes to 4:3 or 2.39:1. The aspect ratio of some signals is fixed to 16:9 depending on the signal format. For details, see "Available Signal Formats" on page 88.  [H Delay]: The picture moves horizontally and a horizontal sync signal appears. Brightness of the picture increases automatically, and makes it easy to check the sync part. When the V Delay button is set to on in H delay mode, a pulse cross picture is displayed.  [V Delay]: The picture moves vertically and a vertical sync signal appears approximately in the center of the screen. The brightness of the picture increases automatically, and makes it easy to check the sync part. When the H Delay button is set to on in V delay mode, a pulse cross picture is displayed.  [External Sync] 1): Sets whether or not to set to the external sync mode when the analog component signal or analog RGB signal is input. When the button is set to on, the signal to be displayed is synchronized with the sync signal input to the EXT SYNC connector (External Sync). When set to off, the signal to be displayed is synchronized with the sync signal included in the signals being monitored (Internal Sync). Note When the button is set to off (Internal Sync), a sync signal is added on the Y signal to monitor the analog component signal and on the G signal to monitor the analog RGB signal.  [Comb] 1): The comb filter is turned on. When the button is set to off, the trap·band-pass filter is selected. When the displayed signal is NTSC, PAL, or PAL-M, this functions.  [Char Off]: The characters on the monitor screen hide during manual adjustment.  [Color Temp]: You can directly access the [Manual Adjust] menu of the [Color Temp Adj] menu. 71 Adjustment Using the Menus