Sony BVME251 Operation Guide - Page 60

[System Configuration] Menu, Network]

Get Sony BVME251 PDF manuals and user guides View all Sony BVME251 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

To set to the native scan mode Set [Native Scan] to [On]. To select the scan mode 1 Set [Native Scan] to [Off]. 2 Select [Scan Mode], then select scan mode from the following. [Normal Scan]: Normal mode [Under Scan]: Under mode [Over Scan]: Over mode Note The scan mode is not selectable in the following cases:  When [Native Scan] is set to [On]  When the internal signal is displayed  When [Side by Side], [Wipe], [Butterfly], or [Blending] is set to [On] [System Configuration] Menu This menu is used to set the system such as the network, parallel remote control function, etc. When [System Configuration] is selected, the following menu is displayed. BVM-E251 BVM-E171 [Network] Sets the remote control function of the network. [Monitor ID] Enter a monitor ID number. Set to 01 to 99. (Default value: [01]) [Group ID] Enter a group ID number. Set to 01 to 99. (Default value: [01]) [Network Setting] Sets the IP address, subnet mask, and default gateway. For the setting value, consult the network administrator. 60 Adjustment Using the Menus

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
Adjustment Using the Menus
60
To set to the native scan mode
Set [Native Scan] to [On].
To select the scan mode
1
Set [Native Scan] to [Off].
2
Select [Scan Mode], then select scan mode from the
following.
[Normal Scan]:
Normal mode
[Under Scan]:
Under mode
[Over Scan]:
Over mode
Note
The scan mode is not selectable in the following cases:
When [Native Scan] is set to [On]
When the internal signal is displayed
When [Side by Side], [Wipe], [Butterfly], or
[Blending] is set to [On]
[System Configuration] Menu
This menu is used to set the system such as the network,
parallel remote control function, etc.
When [System Configuration] is selected, the following
menu is displayed.
BVM-E251
BVM-E171
[Network]
Sets the remote control function of the network.
[Monitor ID]
Enter a monitor ID number.
Set to 01 to 99. (Default value: [01])
[Group ID]
Enter a group ID number.
Set to 01 to 99. (Default value: [01])
[Network Setting]
Sets the IP address, subnet mask, and default gateway.
For the setting value, consult the network administrator.