Yamaha CL3 Cl Editor Owner's Manual - Page 41

If a MATRIX channel is selected, CHANNEL SELECT Channel selection, FROM MIX, ST/MONOC

Get Yamaha CL3 PDF manuals and user guides View all Yamaha CL3 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

If a MATRIX channel is selected ❏ CHANNEL SELECT (Channel selection) Except for the fact that your editing applies to a MATRIX channel, this is the same as the channel selection for a MIX channel (➥ p.37.) ❏ FROM MIX, ST/MONO(C) 1 FROM MIX, ST/MONO(C) send level 1 These adjust the send levels of the signals sent from the MIX 2 buses or STEREO/MONO buses to the MATRIX bus. The cur- 3 rent value is shown in the numerical box immediately below. 4 2 PRE (PRE on/off) These select either PRE or POST as the position from which the signal is sent from the MIX buses or STEREO/MONO buses to the MATRIX bus. PRE EQ or PRE FADER is selected if this is on, or POST FADER is selected if this is off. The PRE EQ/ 1 FADER setting can be made in the Mixer Setup dialogbox. 2 3 3 ON(FROM MIX, ST/MONO send on/off) These are on/off switches for the signal sent from the MIX buses 4 or STEREO/MONO buses to the MATRIX bus. 4 Channel name This section indicates the name of the MIX channel or STEREO/ MONO channel. 41 CL Editor Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
CL Editor Owner’s Manual
41
If a MATRIX channel is selected
❏
CHANNEL SELECT (Channel selection)
Except for the fact that your editing applies to a MATRIX channel, this is the same as the channel selection for a MIX
channel (
➥
p.37.)
❏
FROM MIX, ST/MONO(C)
1
FROM MIX, ST/MONO(C) send level
These adjust the send levels of the signals sent from the MIX
buses or STEREO/MONO buses to the MATRIX bus. The cur-
rent value is shown in the numerical box immediately below.
2
PRE (PRE on/off)
These select either PRE or POST as the position from which the
signal is sent from the MIX buses or STEREO/MONO buses to
the MATRIX bus. PRE EQ or PRE FADER is selected if this is
on, or POST FADER is selected if this is off. The PRE EQ/
FADER setting can be made in the Mixer Setup dialogbox.
3
ON(FROM MIX, ST/MONO send on/off)
These are on/off switches for the signal sent from the MIX buses
or STEREO/MONO buses to the MATRIX bus.
4
Channel name
This section indicates the name of the MIX channel or STEREO/
MONO channel.
2
1
3
4
2
1
3
4