Canon LV-8225 LV-7290 User's Manual - Page 57

Standby mode, Network, P-TIMER, Count up, Count down, 180 Min, Start

Get Canon LV-8225 PDF manuals and user guides View all Canon LV-8225 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 57 highlights

Setting Standby mode This function is available when operating the projector via network. Network..... Supply the power to the network function even after turning off the projector by pressing the POWER button on the remote control unit. You can turn on/off the projector via network, modify network environment, and receive an e-mail about projector status while the projector is powered off. Eco Select Eco when you do not use the projector via network. The projector's network function will stop when turning off the projector, you can not turn on the projector via network. Refer to the user's manual of "Network Set-up and Operation". Note: • When selecting Network, the cooling fans may be running depending on the temperature inside the projector even if the projector is turned off. • When Eco is selected and the projector is in Standby mode, the communication of RS-232C serial port is not available. X: disabled O: enabled Serial command Network Monitor Out Audio Out Direct power on Eco X X X X O Network O O O X *1 O *1 When switch the STANDBY MIC OUT function On in Standby mode status, only MIC volume can be output. P-TIMER P-timer display P-timer This function allows you to change the setting of the Ptimer and execute it. Select one of the following options: Count up........... The P-timer display 000:00 appears on the screen and the count up starts (000:00-180:00) Count down...... The time set in the Timer setting appears on the screen and the countdown starts. Timer Use the Point ▲▼ buttons to set the Timer (1-180 Min). Timer is available in Count down only. Factory default velue is 10 Min. Start It executes the count up or count down function. Press the OK button at Start and the indication changes into Stop. To stop Count up or Count down, press the OK button at Stop on the screen menu, then the indication changes into Restart. Press the OK button at Restart to resume Count up or Count down. Reset Reset the P-timer values. Press the OK button at Reset to return to the following value; Count up ... "000:00" Count down ... Timer that you set Exit To exit the P-timer operation. Stop or Cancel the P-timer via Remote control unit To stop the P-timer function, press the P-TIMER button. To cancel the P-timer, press and hold the P-TIMER button for a few seconds. 57

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
57
Setting
Standby mode
This function is available when operating the projector
via network.
Network
....
Supply the power to the network
function even after turning off the
projector by pressing the POWER
button on the remote control unit.
You can turn on/off the projector via
network, modify network environment,
and receive an e-mail about projector
status while the projector is powered
off.
Eco
............
Select
Eco
when you do not use the
projector via network. The projector’s
network function will stop when turning
off the projector, you can not turn on the
projector via network.
Refer to the user’s manual of “Network Set-up and
Operation”.
Note:
•
When selecting
Network
, the cooling
fans may be running depending on the
temperature inside the projector even if
the projector is turned off.
•
When
Eco
is selected and the projector is
in Standby mode, the communication of
RS-±3±C serial port is not available.
This function allows you to change the setting of the P-
timer and execute it.
Select one of the following options:
Count up
...........
The P-timer display
000:00
appears
on the screen and the count up starts
(
000:00-180:00
)
Count down
......
The time set in the Timer setting
appears on the screen and the
countdown starts.
Timer
.................
Use the Point
▲▼
buttons to set the
Timer (
1-180 Min
).
Timer
is available
in Count down only. Factory default
velue is
10 Min
.
Start
..................
It executes
the count up or count
down function. Press the OK button
at
Start
and the indication changes
into Stop. To stop
Count up
or
Count down
, press the OK button
at
Stop
on the screen menu, then
the indication changes into
Restart
.
Press the OK button at
Restart
to
resume
Count up
or
Count down
.
Reset
.................
Reset the P-timer values.
Press the OK button at
Reset
to
return to the following value;
Count up
... "000:00"
Count down
... Timer that you set
Exit
....................
To exit the P-timer operation.
P-TIMER
P-timer display
Stop or Cancel the P-timer via Remote control unit
To stop the P-timer function, press the P-TIMER button.
To cancel the P-timer, press and hold the P-TIMER
button for a few seconds.
P-timer
X: disabled
O: enabled
*1 When switch the STANDBY MIC OUT function
On
in Standby mode status, only MIC volume
can be output.
Eco
Network
Serial command
X
O
Network
X
O
Monitor Out
X
O
Audio Out
X
X
*1
Direct
power on
O
O