Canon LV-8225 LV-7290 User's Manual - Page 59

Remote control, Lamp mode, If the batteries are removed from

Get Canon LV-8225 PDF manuals and user guides View all Canon LV-8225 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Lamp mode This function allows you to change brightness of the screen. High Brighter than the Normal mode. Normal......... Normal brightness Eco Lower brightness reduces the lamp power consumption and extends the lamp life. Note: • Lamp mode can not be changed for a while after turning on the projector. Lamp needs some time to stabilize after the power is turned on. Stored lamp mode will be active after the lamp is stabilized. Remote control This projector provides two different remote control codes: the factory-set initial code (Code 1) and the secondary code (Code 2). This switching function prevents remote control unit interference when operating several projectors or video equipment at the same time. When operating the projector in Code 2, both the projector and the remote control unit must be switched to Code 2. To change the code for the projector: Select either Code 1 or Code 2 in this Setting Menu. To change the code for the remote control unit: Press and hold both the MENU and IMAGE buttons together for 5 seconds or more. After changing the code, make sure the remote control unit operates properly. Remote control Note: • When different codes are set on the projector and on the remote control unit, any operation cannot be made. In that case, switch the code on the remote control unit to fit the code on the projector. • If the batteries are removed from the remote control unit for a long period of time, the remote control code will be reset. Setting 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
59
Setting
Remote control
This projector provides two different remote control
codes: the factory-set initial code (
Code 1
) and the
secondary code (
Code 2
). This switching function
prevents remote control unit interference when
operating several projectors or video equipment at the
same time.
When operating the projector in
Code 2
, both
the projector and the remote control unit must be
switched to
Code 2
.
To change the code for the proJector:
Select either
Code 1
or
Code 2
in this Setting Menu.
To change the code for the remote control unit:
Press and hold both the MENU and IMAGE buttons
together for 5 seconds or more.
After changing the
code, make sure the remote control unit operates
properly.
Note:
• When different codes are set on the
projector and on the remote control unit,
any operation cannot be made. In that
case, switch the code on the remote
control unit to fit the code on the projector.
•
If the batteries are removed from the
remote control unit for a long period of
time, the remote control code will be reset.
Remote control
This function allows you to change brightness of the
screen.
Lamp mode
Note:
• Lamp mode can not be changed for a
while after turning on the projector. Lamp
needs some time to stabilize after the
power is turned on. Stored lamp mode will
be active after the lamp is stabilized.
High
.............
Brighter than the Normal mode.
Normal
.........
Normal brightness
Eco
..............
Lower brightness reduces the lamp
power consumption and extends
the lamp life.