Compaq ProLiant 5500 Compaq ProLiant 5500 Setup and Installation Guide Pentium - Page 138

Note 1, This contains example cabling scenarios covering the most common

Get Compaq ProLiant 5500 PDF manuals and user guides View all Compaq ProLiant 5500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 138 highlights

7-23 SCSI Cable Usage Matrix for Duplex Mode Continued Note 1: A third SCSI controller card is needed to connect to hard drive backplane SCSI inputs 0 or 1 to support duplex mode operation for this configuration. Note 2: SCSI PORT 2 output will not operate at ultra SCSI speed if non-ultra drives are used in the removable media bay. Note 3: If additional external 50- to 68-pin adapters are needed, order option kit 212055001. Note 4: The loopback SCSI option is not supported by the SMART-2/SL controller. Note 5: The SCSI Port 2 Controller is connected to the SCSI Port 2 connector and external SCSI connector. It is recommended that you use SCSI Port 2 controller for either internal or external drives, not both. Examples This section contains example cabling scenarios covering the most common applications. If your planned configuration does not match one of these examples, use the SCSI Cable Matrices in Tables 7-1 and 7-2 and these examples as a general guide. Compaq ProLiant 5500 Servers Setup and Installation Guide For use with Intel Pentium II Xeon processor-based servers only

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
7-23
Compaq ProLiant 5500 Servers Setup and Installation Guide
For use with Intel Pentium II Xeon processor-based servers only
SCSI Cable Usage Matrix for Duplex Mode
Continued
Note 1:
A third SCSI controller card is needed to connect to hard drive backplane SCSI
inputs 0 or 1 to support duplex mode operation for this configuration.
Note 2:
SCSI PORT 2 output will not operate at ultra SCSI speed if non-ultra drives are used
in the removable media bay.
Note 3:
If additional external 50- to 68-pin adapters are needed, order option
kit 212055-
001.
Note 4:
The loopback SCSI option is not supported by the SMART-2/SL controller.
Note 5:
The SCSI Port 2 Controller is connected to the SCSI Port 2 connector and external
SCSI connector. It is recommended that you use SCSI Port 2 controller for either internal or
external drives, not both.
Examples
This section contains example cabling scenarios covering the most common
applications. If your planned configuration does not match one of these
examples, use the SCSI Cable Matrices in Tables 7-1 and 7-2 and these
examples as a general guide.