Compaq ProLiant 5500 Compaq ProLiant 5500 Setup and Installation Guide Pentium - Page 83

Installing the Duplex Drive Cage Option, into the duplex drive cage.

Get Compaq ProLiant 5500 PDF manuals and user guides View all Compaq ProLiant 5500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

4-18 Installing Hardware Components Installing the Duplex Drive Cage Option Be sure you have followed all the steps under "Accessing the Drive Cage Back Plane" before proceeding with the following steps. 1. Remove any components in the removable media bays and install them into the duplex drive cage. 2. Replace the drive cage. Do not push it back fully until after you install cables. CAUTION: The SCSI backplane board must have a Duplex Enabler board installed in order for the SCSI bus to be terminated properly. If this board is not installed, the service LEDs of all drives will light as a warning. Figure 4-17. Installing the duplex drive cage For use with Intel Pentium II Xeon processor-based servers only

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
4-18
Installing Hardware Components
For use with Intel Pentium II Xeon processor-based servers only
Installing the Duplex Drive Cage Option
Be sure you have followed all the steps under “Accessing the Drive Cage Back
Plane” before proceeding with the following steps.
1.
Remove any components in the removable media bays and install them
into the duplex drive cage.
2.
Replace the drive cage.
Do not push it back fully until after you install
cables.
CAUTION:
The SCSI backplane board must have a Duplex
Enabler board installed in order for the SCSI bus to be terminated
properly. If this board is not installed, the service LEDs of all
drives will light as a warning.
Figure 4-17.
Installing the duplex drive cage