Compaq ProLiant 5500 Compaq ProLiant 5500 Setup and Installation Guide Pentium - Page 85

Connect SCSI controller cables. See Cabling, for, Replace fans.

Get Compaq ProLiant 5500 PDF manuals and user guides View all Compaq ProLiant 5500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

4-20 Installing Hardware Components 4. Pull out the drive cage latch and push the drive cage back fully until the drive cage latch can be pushed into place. 5. Tighten the thumbscrews on the front of the drive cage. 6. Connect SCSI controller cables. See Chapter 7, "Cabling," for information on SCSI cabling. Figure 4-19 shows an example controller connection. Figure 4-19. Example cable connection to SCSI controller 7. Replace fans. For use with Intel Pentium II Xeon processor-based servers only

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
4-20
Installing Hardware Components
For use with Intel Pentium II Xeon processor-based servers only
4.
Pull out the drive cage latch and push the drive cage back fully until the
drive cage latch can be pushed into place.
5.
Tighten the thumbscrews on the front of the drive cage.
6.
Connect SCSI controller cables. See Chapter 7, “Cabling,” for
information on SCSI cabling. Figure 4-19 shows an example controller
connection.
Figure 4-19.
Example cable connection to SCSI controller
7.
Replace fans.