Compaq ProLiant 5500 Compaq ProLiant 5500 Setup and Installation Guide Pentium - Page 69

Accessing the Processor, Processor Power Module PPM.

Get Compaq ProLiant 5500 PDF manuals and user guides View all Compaq ProLiant 5500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

4-4 Installing Hardware Components 7. Slide the side cover toward the rear of the unit about 1 inch (2.5 cm); then remove the cover. Figure 4-1. Removing the server cover Accessing the Processor The ProLiant 5500 server is shipped with one processor module and three terminator boards which fill all of the processor sockets. When adding processors, first remove the terminator board and then install the processor and Processor Power Module (PPM). For use with Intel Pentium II Xeon processor-based servers only

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
4-4
Installing Hardware Components
For use with Intel Pentium II Xeon processor-based servers only
7.
Slide the side cover toward the rear of the unit about 1 inch (2.5 cm);
then remove the cover.
Figure 4-1.
Removing the server cover
Accessing the Processor
The ProLiant 5500 server is shipped with one processor module and three
terminator boards
which fill all of the processor sockets. When adding
processors, first remove the terminator board and then install the processor and
Processor Power Module (PPM).