Dell DX6004S Hardware Owner's Manual - Page 106

iDRAC6 Express Card, Installing an iDRAC6 Express Card

Get Dell DX6004S PDF manuals and user guides View all Dell DX6004S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 106 highlights

2 Lower the fan into the fan assembly until the fan is fully seated. See Figure 3-13. 3 Connect the fan's power cable to the power connector on the system board. 4 Replace the cooling shroud or power distribution board shroud as applicable. See "Installing the Cooling Shroud" on page 95. 5 Close the system. See "Closing the System" on page 77. 6 Reconnect the system to its electrical outlet and turn the system on, including any attached peripherals. iDRAC6 Express Card Installing an iDRAC6 Express Card CAUTION: Many repairs may only be done by a certified service technician. You should only perform troubleshooting and simple repairs as authorized in your product documentation, or as directed by the online or telephone service and support team. Damage due to servicing that is not authorized by Dell is not covered by your warranty. Read and follow the safety instructions that came with the product. 1 Turn off the system, including any attached peripherals, and disconnect the system from the electrical outlet. 2 Open the system. See "Opening the System" on page 76. 3 If installed, remove the expansion card from the expansion-card slot. See "Removing an Expansion Card" on page 88. 4 Insert the notch on the iDRAC6 Express card into the clip on the system board. 5 Align the front edge of the card with the connector on the system board. See Figure 6-1 for the location of the connector. 6 Press the card down until it is fully seated. See Figure 3-14. When the front of the card is fully seated, the plastic standoff tab snaps over the edge of the holder. 106 Installing System Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
106
Installing System Components
2
Lower the fan into the fan assembly until the fan is fully seated.
See Figure 3-13.
3
Connect the fan’s power cable to the power connector on the system board.
4
Replace the cooling shroud or power distribution board shroud as applicable.
See "Installing the Cooling Shroud" on page 95.
5
Close the system. See "Closing the System" on page 77.
6
Reconnect the system to its electrical outlet and turn the system on, including
any attached peripherals.
iDRAC6 Express Card
Installing an iDRAC6 Express Card
CAUTION:
Many repairs may only be done by a certified service technician. You
should only perform troubleshooting and simple repairs as authorized in your
product documentation, or as directed by the online or telephone service and
support team. Damage due to servicing that is not authorized by Dell is not covered
by your warranty. Read and follow the safety instructions that came with the
product.
1
Turn off the system, including any attached peripherals, and disconnect
the system from the electrical outlet.
2
Open the system. See "Opening the System" on page 76.
3
If installed, remove the expansion card from the expansion-card slot.
See "Removing an Expansion Card" on page 88.
4
Insert the notch on the iDRAC6 Express card into the clip on the system
board.
5
Align the front edge of the card with the connector on the system board.
See
Figure 6-1
for the location of the connector.
6
Press the card down until it is fully seated. See Figure 3-14.
When the front of the card is fully seated, the plastic standoff tab snaps
over the edge of the holder.