Dell PowerEdge 4350 Dell PowerEdge 4350 Systems Installation and Troubleshooti - Page 120

Unsnap the retaining clip from the guide bracket assembly and remove the clip.

View all Dell PowerEdge 4350 manuals Add to My Manuals Save this manual to your list of manuals

• 
  1
• 
  2
• 
  3
• 
  4
• 
  5
• 
  6
• 
  7
• 
  8
• 
  9
• 
  10
• 
  11
• 
  12
• 
  13
• 
  14
• 
  15
• 
  16
• 
  17
• 
  18
• 
  19
• 
  20
• 
  21
• 
  22
• 
  23
• 
  24
• 
  25
• 
  26
• 
  27
• 
  28
• 
  29
• 
  30
• 
  31
• 
  32
• 
  33
• 
  34
• 
  35
• 
  36
• 
  37
• 
  38
• 
  39
• 
  40
• 
  41
• 
  42
• 
  43
• 
  44
• 
  45
• 
  46
• 
  47
• 
  48
• 
  49
• 
  50
• 
  51
• 
  52
• 
  53
• 
  54
• 
  55
• 
  56
• 
  57
• 
  58
• 
  59
• 
  60
• 
  61
• 
  62
• 
  63
• 
  64
• 
  65
• 
  66
• 
  67
• 
  68
• 
  69
• 
  70
• 
  71
• 
  72
• 
  73
• 
  74
• 
  75
• 
  76
• 
  77
• 
  78
• 
  79
• 
  80
• 
  81
• 
  82
• 
  83
• 
  84
• 
  85
• 
  86
• 
  87
• 
  88
• 
  89
• 
  90
• 
  91
• 
  92
• 
  93
• 
  94
• 
  95
• 
  96
• 
  97
• 
  98
• 
  99
• 
  100
• 
  101
• 
  102
• 
  103
• 
  104
• 
  105
• 
  106
• 
  107
• 
  108
• 
  109
• 
  110
• 
  111
• 
  112
• 
  113
• 
  114
• 
  115
• 
  116
• 
  117
• 
  118
• 
  119
• 
  120
• 
  121
• 
  122
• 
  123
• 
  124
• 
  125
• 
  126
• 
  127
• 
  128
• 
  129
• 
  130
• 
  131
• 
  132
• 
  133
• 
  134
• 
  135
• 
  136
• 
  137
• 
  138
• 
  139
• 
  140
• 
  141
• 
  142
• 
  143
• 
  144
• 
  145
• 
  146
• 
  147
• 
  148
• 
  149
• 
  150
• 
  151
• 
  152
• 
  153
• 
  154
• 
  155
• 
  156
• 
  157
• 
  158
• 
  159
• 
  160
• 
  161
• 
  162
• 
  163
• 
  164
• 
  165
• 
  166
• 
  167
• 
  168
• 
  169
• 
  170
• 
  171
• 
  172
• 
  173
• 
  174
• 
  175
• 
  176
• 
  177
• 
  178
• 
  179
• 
  180
• 
  181
• 
  182
• 
  183
• 
  184
• 
  185
• 
  186
• 
  187
• 
  188
• 
  189
• 
  190
• 
  191
• 
  192
• 
  193
• 
  194
• 
  195
• 
  196
• 
  197
• 
  198
• 
  199
• 
  200
• 
  201
• 
  202
• 
  203
• 
  204
• 
  205
• 
  206
• 
  207
• 
  208

Match case Limit results 1 per page

---

100% Actual Size Fit Width Fit Height Fit Page Automatic

8-12

Dell PowerEdge

4350 Systems Installation and Troubleshooting Guide

8SJUDGLQJ±WKH±0LFURSURFHVVRU±RU±

,QVWDOOLQJ±DQ±$GGLWLRQDO±0LFURSURFHVVRU

&$87,21±²,I²\RX²DUH²DGGLQJ²D²PLFURSURFHVVRU²WR²\RXU²V\VWHP´²\RX²PXVW²

RUGHU²DQ²XSJUDGH²NLW²IURP²’HOOµ²7KH²XSJUDGH²NLW²FRQWDLQV²WKH²FRUUHFW²

YHUVLRQ²RI²PLFURSURFHVVRU²IRU²\RXU²V\VWHPµ

The microprocessor is contained within a single-edge contact (SEC) cartridge and heat

sink assembly. The system board has two guide bracket assemblies that hold the SEC

cartridge and heat sink assemblies. If your system has only one microprocessor, the

unused guide-bracket assembly connector

must

contain a terminator card. If you are

adding a microprocessor, it must have the same operating frequency as the installed

microprocessor. For example, if the system has a 400-MHz microprocessor, the addi-

tional microprocessor must also be a 400-MHz microprocessor.

5HPRYLQJ±D±7HUPLQDWRU±&DUG

Use the following procedure, which is illustrated in Figure 8-8, to remove a terminator

card from a guide bracket assembly. See the appropriate procedure depending on

which terminator card you are using.

For a terminator card with a retaining clip that separates from the terminator card (see

Figure 8-8), do the following:

1.

Unsnap the retaining clip from the guide bracket assembly and remove the clip.

Using the thumb and forefinger of each hand, pinch the vertical tabs at each end

of the retaining clip and lift the clip straight up.

2.

Slide the terminator card up and out of the guide bracket assembly.

For a terminator card with a retaining clip that does not separate from the terminator

card (see Figure 8-8), do the following:

1.

Using the thumb and forefinger of each hand, pinch the vertical tabs at each end

of the retaining clip.

2.

Slide the terminator card up and out of the guide bracket assembly.