Dell PowerEdge R840 EMC Installation and Service Manual - Page 109

Optional IDSDM or vFlash module

Get Dell PowerEdge R840 PDF manuals and user guides View all Dell PowerEdge R840 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 109 highlights

Figure 75. Installing a processor and 2U heat sink module Next steps 1. Install the air shroud. 2. Follow the procedure listed in After working inside your system on page 45 Optional IDSDM or vFlash module NOTE: The write-protect switch is on the IDSDM or vFlash module. Removing IDSDM or vFlash module Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 44. 2. Follow the procedure listed in Before working inside your system on page 45. 3. Remove the air shroud. 4. Remove the expansion card riser 1. Steps 1. Locate the IDSDM or vFlash connector on riser 1. 2. Holding the pull tab, lift the IDSDM or vFlash module out of the system. Installing and removing system components 109

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Figure 75. Installing a processor and 2U heat sink module
Next steps
1.
Install the air shroud
.
2.
Follow the procedure listed in
After working inside your system
on page 45
Optional IDSDM or vFlash module
NOTE:
The write-protect switch is on the IDSDM or vFlash module.
Removing IDSDM or vFlash module
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 44.
2.
Follow the procedure listed in
Before working inside your system
on page 45.
3.
Remove the air shroud
.
4.
Remove the expansion card riser 1
.
Steps
1.
Locate the IDSDM or vFlash connector on riser 1.
2.
Holding the pull tab, lift the IDSDM or vFlash module out of the system.
Installing and removing system components
109