Dell PowerEdge R840 EMC Installation and Service Manual - Page 144

Installing left control panel

Get Dell PowerEdge R840 PDF manuals and user guides View all Dell PowerEdge R840 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 144 highlights

Figure 113. Removing left control panel Next steps 1. Install the left control panel. Installing left control panel Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 44. 2. Follow the procedure listed in Before working inside your system on page 45. 3. Remove the non-GPU air shroud or GPU air shroud. 4. Remove the cooling fan assembly. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. To prevent the cables from being pinched or crimped, you must route the cables properly when you replace them. Steps 1. Route the control panel cable through the side wall of the system. 2. Align the control panel assembly with the control panel slot on the system and attach the control panel assembly to the system. 3. Connect the control panel cable to the system board connector. 4. Close the cable latch to secure the control panel cable. 5. Using a Phillips #1 screwdriver, install the screws that secure the control panel and ribbon cable to the system. 144 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Figure 113. Removing left control panel
Next steps
1.
Install the left control panel
.
Installing left control panel
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 44.
2.
Follow the procedure listed in
Before working inside your system
on page 45.
3.
Remove the non-GPU air shroud
or
GPU air shroud
.
4.
Remove the cooling fan assembly
.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. To prevent the cables
from being pinched or crimped, you must route the cables properly when you replace them.
Steps
1.
Route the control panel cable through the side wall of the system.
2.
Align the control panel assembly with the control panel slot on the system and attach the control panel assembly to the system.
3.
Connect the control panel cable to the system board connector.
4.
Close the cable latch to secure the control panel cable.
5.
Using a Phillips #1 screwdriver, install the screws that secure the control panel and ribbon cable to the system.
144
Installing and removing system components