Dell PowerEdge R840 EMC Installation and Service Manual - Page 66

Rear drive cage, Removing the rear drive cage

Get Dell PowerEdge R840 PDF manuals and user guides View all Dell PowerEdge R840 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

NOTE: When installing a drive into the drive carrier, ensure that the screws are torqued to 4 in-lbs. Figure 40. Installing a drive into the drive carrier Next steps 1. Install the drive carrier. 2. If applicable, install the front bezel. 3. Follow the procedure listed in After working inside your system on page 45. Rear drive cage The rear drive cage supports up to two 2.5 inch drives. Removing the rear drive cage Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 44. 2. Follow the procedure listed in Before working inside your system on page 45. 3. Remove the air shroud. 4. Remove all the drives. 5. Disconnect all the cables from the rear drive backplane. Steps 1. Using a Phillips #2 screwdriver, loosen the screws that secure the drive cage to the system. 2. Hold the drive cage and lift it away from the system. 66 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
NOTE:
When installing a drive into the drive carrier, ensure that the screws are torqued to 4 in-lbs.
Figure 40. Installing a drive into the drive carrier
Next steps
1.
Install the drive carrier
.
2.
If applicable,
install the front bezel
.
3.
Follow the procedure listed in
After working inside your system
on page 45.
Rear drive cage
The rear drive cage supports up to two 2.5 inch drives.
Removing the rear drive cage
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 44.
2.
Follow the procedure listed in
Before working inside your system
on page 45.
3.
Remove the air shroud
.
4.
Remove all the drives
.
5.
Disconnect all the cables from the rear drive backplane.
Steps
1.
Using a Phillips #2 screwdriver, loosen the screws that secure the drive cage to the system.
2.
Hold the drive cage and lift it away from the system.
66
Installing and removing system components