Dell PowerEdge R840 EMC Installation and Service Manual - Page 65

Removing the drive from the drive carrier, Installing a drive into the drive carrier

Get Dell PowerEdge R840 PDF manuals and user guides View all Dell PowerEdge R840 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Removing the drive from the drive carrier Prerequisites 1. Follow the safety guidelines listed in Safety instructions. CAUTION: Mixing drive carriers from previous generations of PowerEdge servers is not supported. 2. Follow the procedure listed in Before working inside your system. 3. If installed, remove the front bezel. 4. Remove the drive carrier. Steps 1. Using a Phillips #1 screwdriver, remove the screws from the slide rails on the drive carrier. 2. Lift the drive out of the drive carrier. Figure 39. Removing the drive from the drive carrier Next steps 1. Install the drive into the drive carrier. Installing a drive into the drive carrier Prerequisites 1. Follow the safety guidelines listed in Safety instructions. 2. Follow the procedure listed in Before working inside your system. 3. If installed, remove the front bezel. 4. Remove the drive carrier. CAUTION: Mixing drive carriers from other generations of PowerEdge servers is not supported. Steps 1. Insert the drive into the drive carrier with the connector end of the drive towards the back of the carrier. 2. Align the screw holes on the drive with the screws holes on the drive carrier. When aligned correctly, the back of the drive is flush with the back of the drive carrier. 3. Using a Phillips #1 screwdriver, secure the drive to the drive carrier with screws. Installing and removing system components 65

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Removing the drive from the drive carrier
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
CAUTION:
Mixing drive carriers from previous generations of PowerEdge servers is not supported.
2.
Follow the procedure listed in
Before working inside your system
.
3.
If installed,
remove the front bezel
.
4.
Remove the drive carrier
.
Steps
1.
Using a Phillips #1 screwdriver, remove the screws from the slide rails on the drive carrier.
2.
Lift the drive out of the drive carrier.
Figure 39. Removing the drive from the drive carrier
Next steps
1.
Install the drive into the drive carrier
.
Installing a drive into the drive carrier
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
.
2.
Follow the procedure listed in
Before working inside your system
.
3.
If installed,
remove the front bezel
.
4.
Remove the drive carrier
.
CAUTION:
Mixing drive carriers from other generations of PowerEdge servers is not supported.
Steps
1.
Insert the drive into the drive carrier with the connector end of the drive towards the back of the carrier.
2.
Align the screw holes on the drive with the screws holes on the drive carrier.
When aligned correctly, the back of the drive is flush with the back of the drive carrier.
3.
Using a Phillips #1 screwdriver, secure the drive to the drive carrier with screws.
Installing and removing system components
65