Dell PowerEdge R840 EMC Installation and Service Manual - Page 127

Installing USB 3.0 module

Get Dell PowerEdge R840 PDF manuals and user guides View all Dell PowerEdge R840 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 127 highlights

2. Using the Phillips #2 screwdriver, loosen the screw on the USB 3.0 module. 3. Slide the USB 3.0 module out of the system. Figure 100. Removing USB 3.0 module Next steps 1. Replace the USB 3.0 module. Installing USB 3.0 module Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 44. 2. Follow the procedure listed in Before working inside your system on page 45. 3. Remove the air shroud. 4. Remove the cooling fan assembly. Steps 1. Route the power and the USB cables on the USB 3.0 module through the USB 3.0 module slot on the front of the system. 2. Insert the USB 3.0 module into the slot on the front panel. 3. Align the screw on the module with the screw hole on the system. 4. Using a Phillips #2 screwdriver, tighten the screw to secure the module to the system. 5. Route and connect the USB cable to internal USB port and power cable to the backplane power connector on the system board. To locate the connector, see the System board jumpers and connectors section. Installing and removing system components 127

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
2.
Using the Phillips #2 screwdriver, loosen the screw on the USB 3.0 module.
3.
Slide the USB 3.0 module out of the system.
Figure 100. Removing USB 3.0 module
Next steps
1.
Replace the USB 3.0 module
.
Installing USB 3.0 module
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 44.
2.
Follow the procedure listed in
Before working inside your system
on page 45.
3.
Remove the air shroud
.
4.
Remove the cooling fan assembly
.
Steps
1.
Route the power and the USB cables on the USB 3.0 module through the USB 3.0 module slot on the front of the system.
2.
Insert the USB 3.0 module into the slot on the front panel.
3.
Align the screw on the module with the screw hole on the system.
4.
Using a Phillips #2 screwdriver, tighten the screw to secure the module to the system.
5.
Route and connect the USB cable to internal USB port and power cable to the backplane power connector on the system board. To
locate the connector, see the
System board jumpers and connectors
section.
Installing and removing system components
127