Dell PowerEdge R840 EMC Installation and Service Manual - Page 146

Installing right control panel

Get Dell PowerEdge R840 PDF manuals and user guides View all Dell PowerEdge R840 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 146 highlights

Figure 115. Removing right control panel Next steps 1. Replace the right control panel. Installing right control panel Prerequisites 1. Follow the safety guidelines listed in Safety instructions on page 44. 2. Follow the procedure listed in Before working inside your system on page 45. 3. Remove front bezel, if installed. 4. Remove drives, optical drive, or drive blanks, if installed. 5. Remove the air shroud. 6. Remove the cooling fan assembly. NOTE: Ensure that you note the routing of the cables as you remove them from the system board. To prevent the cables from being pinched or crimped, you must route the cables properly when you replace them. Steps 1. Route the control panel cable and VGA cable through the side wall of the system. 2. Align the control panel with the control panel slot on the system and attach the control panel to the system. 3. Connect the VGA cable to the system board. 4. Connect the control panel cable to the system board and secure it using cable latch. 5. Using a Phillips #1 screwdriver, install the screws that secure the control panel and ribbon cable to the system. 146 Installing and removing system components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Figure 115. Removing right control panel
Next steps
1.
Replace the right control panel
.
Installing right control panel
Prerequisites
1.
Follow the safety guidelines listed in
Safety instructions
on page 44.
2.
Follow the procedure listed in
Before working inside your system
on page 45.
3.
Remove front bezel
, if installed.
4.
Remove drives
,
optical drive
, or
drive blanks
, if installed.
5.
Remove the air shroud
.
6.
Remove the cooling fan assembly
.
NOTE:
Ensure that you note the routing of the cables as you remove them from the system board. To prevent the cables
from being pinched or crimped, you must route the cables properly when you replace them.
Steps
1.
Route the control panel cable and VGA cable through the side wall of the system.
2.
Align the control panel with the control panel slot on the system and attach the control panel to the system.
3.
Connect the VGA cable to the system board.
4.
Connect the control panel cable to the system board and secure it using cable latch.
5.
Using a Phillips #1 screwdriver, install the screws that secure the control panel and ribbon cable to the system.
146
Installing and removing system components